Test Case

Show / Hide direct link   <MAIN> 2642PA: Network Installation & Basic Function Test - PP-80425



Version 2.3
Created on 26/09/2002 21:10:46  by Muralidharan Seshadri
Summary
Preconditions
Status:   New
Priority:   Medium
BASIC INFORMATION
Section:S/W Test Require attachment:No
Team:Network Group:Basic Function
Lessons Learned:Yes Phase:SIV (BBFV), SIT
Locations:Inhouse: AWS and Cambridge, Inhouse: AWS, Inhouse: Cambridge, Compal, Flextronics, Quanta, Wistron Owned By:Eiji Ogata/LENOVO
Objective:To install and configure network driver for Mini-PCI / Onboard ethernet
CRITERIA
Network driver should be able to install/uninstall.
EUT QUANTITY
One system
EQUIPMENT
PPA networking facilities
Critical Attribute:[0] : ETN - Ethernet

CONFIGURATION
REFERENCE PROCEDURE
Note : Perform this test in Battery mode as much as possible




SCOPE
  • Setup and configure adapter ? (adapter cards, Thinkpad , dockingstation ... )
  • Connect network ? ( Ethernet , TokenRing )
  • Use network via all functionable protocol ? ( NetBEUI , IPX/SPX , TCP/IP ...)
  • No error under heavy tasks ? ( copy large files , longrun , start many tasks ... )
  • ThinkPad related function ? ( PM mode , PCI bus ... )
  • Use network application ? ( Internet Exproler , Lotus Notes , MS Office ...)

PREPERATION

Add System Monitor

  1. Open System Monitor (Fig.1). Performance should be watched everytime network is tested.(In the System Monitor Go To Edit Menu -> Add items ->Add the Item 'Microsoft Network Client Read/sec' and 'Microsoft Network Client Write/sec'.
  2. Check network performance according to nominal value described in CRITERIA section

Fig.1 SYSTEM MONITOR



INSTALLATION
  1. Insert adapter (Hot plug-In) and configure it according to User's guide of adapter. Check default parameters that OEM recommends to use.
  2. Bind protocol stacks (NetBEUI,IPX/SPX,TCP/IP).
  3. Reboot the system and confirm adapter is working.
  4. Reboot 3 times for each Cold and Warm. Confirm adapter is working fine.


PLUG & PLAY

No

NBT (NetBIOS over TCP/IP)

  1. Boot the system in AC mode
  2. Login to Windows NT Server
  3. Open system monitor (see PREPERATION section)
  4. Copy & Compare files for specific time duration (see EXPECTED). Use common Long run program. Plug-out / in AC jack while transfering file. Make sure that this operation does not cause a file transfer error or performance down.
    1. Running in AC mode for 1 min
    2. Remove AC jack and running in Battery mode for 1 min
    3. Repeat steps 1 to 2 for 3 times
    4. Running the system until the specified duration.

      EXPECTED:
      For 15 min, no error for MID priority adapter, For 4 hours, no error for HIGH priority adapter
      Performance should be greater than CRITERIA in bath READ and WRITE.
      No performance degradation in battery mode against AC mode.
  5. More than 300MB file transfer should be no problem
POWER MANAGEMENT
  1. Stand-by while cnnecting Network
    EXPECTED: Refer to Table-1 in Criteria
  2. Suspend / Resume while cnnecting Network
    EXPECTED: Refer to Table-1 in Criteria
  3. Hibernation while connecting Network
    EXPECTED: Refer to Table-1 in Criteria
  4. Stop adapter and remove it, and then hibernate fully.
  5. Wake up the system.
    EXPECTED: System resumes network connection again.
  6. This is the end of NetBEUI section and continue to IPX section.
  7. Change Solt to the other (Slot1 -> Slot2 or Vise Versa) *1

TCP/IP

  1. Boot the system in Battery mode.
  2. Connect to network.
  3. PING w/ 64 Byte packets in continuous mode. Stand-by while PING is running 3 times (in any mode, Stand-by should not disconnect the network connection).
  4. Suspend and then Resume 3 times (in battery mode, the system should enter into fulll suspend mode).
  5. PING w/ greater than 1516 Byte packets.
  6. Hibernate, and then wake up 3 times (in battery mode, the system should enter into ibernation).
  7. Change Solt to the other (Slot1 -> Slot2 or Vise Versa) *1
  8. Change power mode from Battery to AC
  9. Login to FTP Server.
  10. MGET files. Plug-out / in AC jack while transfering file.
    EXPECTED:
    For 15 min, no error for MID and LOW priority adapter.
  11. Change power mode from AC to Battery
  12. MGET files. Plug-out / in AC jack while transfering file.
    EXPECTED:
    For 15 min, no error for MID and LOW priority adapter.

STATISTIC INFO
Operating System Win81-64bit Win81-32bit Win10-32bit Win10-64bit Win7- 64bit Win7- 32bit Total
Test Points
Duration
Workload
# Step actions Win81-64bitWin81-32bitWin10-32bitWin10-64bitWin7- 64bitWin7- 32bit
1 Installation AAAAAA
2 Basic Network Functions AAAAAA
3 Basic Gigabit Ethernet Verification AAAAAA
4 Network stability test using Cross Over cable AAAAAA
5 Network Diagnostics Framework (NDF) AAAAAA
DETAILS
ATTENTION!! Please follow below information.
1. Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead, then arrange to open defect, if needed.

2. Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case).

3. All Test Activity should be performed with AMT Enabled as Default (applicable on vPro enabled systems).

4. Please check Usability / Cosmetic issues (correct sentence/appropriate display/etc.) and open defect, if needed.

Perform this test in User mode and Admin mode.
Network Driver
WinXP
Win 7
Administrator Mode
User Mode
Administrator Mode
User Mode
Installation
A
A
A
A
Overwrite/update installatoin
A
A
A
A
DOS driver utility
A
A
A
A



Note :
  1. Update the EEPROM utility for Gigabit Ethernet and 10/100Mbps ethernet.
  2. Install the correct driver for Gigabit ethernet and 10/100Mbps ethernet.
3. Read Build Letter for procedure/restrictions.

Installation
Test Item Config
Result
Win XP
Win 7
Installation (user mode)
- Install the driver in user mode using setup
- Criteria : User should not be able to install the driver
- Uninstall the application from 'Add/Remove programs'
Criteria : User should not be able to uninstall the driver

Installation (Admin Mode)
For Intel Ethernet Adapter:
- Install the driver in Admin mode using setup INF installation
- Check that the installation is successful
- Uninstall the driver from 'Device Manager'
- Confirm that application is removed completly.
- Install the application again.
- Check for the correct driver version/date in the device manager

For Broadcom Ethernet Adapter:
- Install the driver using INF and Setup (path /DRVINST/SETUP.exe) installation
- Check that the installation is successful.
- Check for the correct driver version/date in the device manager
- Uninstall the driver from Device Manager-INF or Add/Remove Programs-Setup
- Confirm that driver/application is removed completely.
- Install the driver again using INF and Setup (path /DRVINST/SETUP.exe) installation
- Check that the installation is successful.
- Check for the correct driver version/date in the device manager.

For Realtek Ethernet Adapter
- Install the driver using INF and Setup installation
- Check that the installation is successful.
- Check for the correct driver version/date in the device manager
- Uninstall the driver from Device Manager-INF or Add/Remove Programs-Setup
- Confirm that driver/application is removed completely.
- Install the driver again using INF and Setup installation
- Check that the installation is successful.
- Check for the correct driver version/date in the device manager.
Stand aloneStand alone
A
A
Perform the driver installation
a) Using setup option
b) Using Inf installation

Overwrite/Update Installation
- Perform overwrite installation for the same driver version (INF or Setup.exe installation)
- Check that the driver can be installed properly and no malfunction occurs
- Perform update installation from the previous version (INF and Setup.exe installation)
- Check for the driver date and version.
Stand aloneStand alone
A
A
Options Verifications
In Device manager, select the ethernet adapter, double click to select the properties.
In Advanced tab, Verify the options listed there and its functions.
In Power Management tab, Verify the options listed are checked by default.
Stand alone
A
A
Network Driver utilities and options verifications
  1. Install Intel Proset and other related utilites that comes with the package.
  2. Check for all the options like Intel Priority Packet / Packet protect.
  3. Configure all the options and check for Proset and IP security functions
  4. Confirm all the functions after PM
Stand alone
A
A
Local Area Network Disable/Enable Verification -UR2506
1. In Windows XP, Go to control panel->Network Connections->Right click and disable Local Area Connection

2. In Vista, In Control Panel->Network and Sharing Center->Manage Network Connection->Right-click and Disable Local Area Connection

3. In Windows 7, In Control Panel->Network and Sharing Center->Change Adapter Setting->Right-click and Disable Local Area Connection

4. Suspend the system then Resume
5. Check if the Local Area Connection is still disabled
6. Enable the Local Area Connection and check for Network functionality
7. Hibernate the system then Resume
8. Check if the Local Area Connection is still disabled
9. Enable the Local Area Connection and check for Network functionality


Expected: The Local Area Connection should get disabled/enable in Network Connections and no error message should appear

Reference CMVC:
#91644, WXP:Intel Ethernet cannot be disabled in Network connections
Stand alone
A
A


Note :
Perform all the tests in Battery Mode as much as possible (wherever applicable)
Perform this test in Admin mode and user mode in Windows XP/Windows 2000 and Windows NT


Basic Network functions
TEST ITEM
Results
Win XP
Win 7
Windows NT (TCP/IP, NetBEUI)
1.Configure TCP/IP (Static IP address) only
2.Ping to server with 2048 bytes
3.Download files using ftp
4.Configure TCP/IP (DHCP) only
5.Download files using ftp (>300MB files)
6.Configure Internet Explorer 5 (or latest)
7.Download files from the internet
8.Configure NetBEUI only
9.Map shared network directory and copy files.
10.Configure TCP/IP and NetBEUI
11.Using FTP download files of >300 MB
12.Using shared directory copy files of > 300 MB


FUNCTION
No.
ITEM
Results
Win XP
Win 7
Basic (NBT)
1
Login to Windows NT Server
2
Copy & Compare files. Copy more than 500MB size single file.
3
Plug-out / in AC jack while transfering file
Basic (TCP/IP)
1
Boot the system (Power on)
2
PING w/ 64 Byte packets. Stand-by while PING is running (x3, confirm network does not loose connection).
3
Suspend / Resume (x3, confirm full suspend)
4
PING w/ greater than 1516 Byte packets
5
Hibernate the system
6
Wake up (x3, confirm hibernation)
7
Login to FTP Server
8
MGET files (15 min -or- 4 hour)
9
Plug-out / in AC jack while transfering file
10
MGET files (15 min -or- 4 hour)
Dock / Undock
1
Hot dock / Undock
2
Warm dock / Undock
3
Confirm network connection by PING w/ greater than 1516 Byte packets


Basic Network functions - UR2649SG
TEST ITEM
Results
Win XP
Win 7
In Device Manager->Network Adapters->Select the Ethernet adapter. Double click to select the properties.
In Advanced tab, verify the all options available in property window.
1. Select the Link speed & Duplex option
confirm all the options are listed and when selected works fine.
100 Mbps/full duplex, 100 Mbps/Half duplex, 10 Mbps/full Duplex, 10Mbps/Half duplex
Auto detec.
Note : For 1Gig ethernet system, 1000 Mbps/Full duplex option will be listed

For Broadcom ethernet adapters:
The following options should be available in property window from Advanced tab.
- Etherent@WireSpeed
- Flow Control
- Interrupt Moderation
- Large Send Offload(IPV4)
- Large Send Offload v2 (IPV4)
- Network Address
- Priority & VLAN
- Speed & Duplex
- TCP/UDP Checksum Offload (IPV4)
- TCP/UDP Checksum Offload (IPV6)
- VLAN ID
- Wake On Link
- Wake Up Capabilities
- WOL Speed

For Intel Ethernet adapters
The following options should be available in property window from Advanced tab.

Windows XP:
- Adaptive Inter-Frame Spacing
- Enable PME
- Flow Control
- Gigabit Master Slave Mode
- Interrupt Moderation / Interrupt Moderation Rate
- IPv4 Checksum Offload
- Jumbo Packet
- Link Speed & Duplex
- Link Speed Battery Saver
- Locally Administered Address
- Log Link State Event
- Priority & VLAN
- Receive buffers
- TCP Checksum Offload (IPV4)
- Transmit Buffers
- UDP Checksum Offload (IPV4)
- Wait for Link
- Wake on Link Settings
- Wake on Setting

Windows Vista:
- Adaptive Inter-Frame Spacing
- Enable PME
- Flow Control
- Gigabit Master Slave Mode
- Interrupt Moderation / Interrupt Moderation Rate
- IPv4 Checksum Offload
- Jumbo Packet
- Large Send Offload (IPv4/IPv6) - Vista
- Link Speed & Duplex
- Link Speed Battery Saver - winxp and vista
- Locally Administered Address
- Log Link State Event
- Priority & VLAN
- Receive Buffers
- Receive Side Scaling
- Receive Side Scaling Queues
- System Idle Power Saver
- TCP Checksum Offload (IPV4/IPV6)
- Transmit Buffers
- UDP Checksum Offload (IPV4/IPV6)
- Wait for Link
- Wake on Link Settings
- Wake on Setting

Windows 7:
- Adaptive Inter-Frame Spacing
- Enable PME
- Flow Control
- Gigabit Master Slave Mode
- Interrupt Moderation / Interrupt Moderation Rate
- IPv4 Checksum Offload
- Jumbo Packet
- Large Send Offload v2 (IPV4/IPV6)
- Link Speed & Duplex
- Locally Administered Address
- Log Link State Event
- Priority & VLAN
- Receive buffers
- Receive Side Scaling
- Receive Side Scaling Queues
- System Idle Power Saver
- TCP Checksum Offload (IPV4/IPV6)
- Transmit Buffers
- UDP Checksum Offload (IPV4/IPV6)
- Wait for Link
- Wake on Link Settings
- Wake on Magic Packets
- Wake on Pattern Match

For Realtek Ethernet adapters
The following options should be available in property window from Advanced tab.

- Auto Disable Gigabit (PowerSaving)
- Flow Control
- Green Ethernet
- Interrupt Moderation
- IPv4 Checksum Offload
- Jumbo Frame
- Large Send Offload v2 (IPv4)
- Large Send Offload v2 (IPv6)
- Network Address
- Priority & VLAN
- Receive Buffers
- Receive Side Scaling
- Shutdown Wake-On-Lan
- Speed & Duplex
- TCP Checksum Offload (IPv4/IPv6)
- Transmit Buffers
- UDP Checksum Offload (IPv4/IPv6)
- Wake on Magic Packet
- Wake on Pattern Match
- WOL & Shutdown Link Speed

Set diffrent values and check the functionality.
Make sure no yellow marks appear after changing values in the device manager.

Reference #ECR10428 W7:Yellow mark in devmgr if Link Speed changed w/Intel Eth
A
A
For Japanese OS : (LL-01012PA)
- Verify the text shown in GUI are correct. Also verify the help file for the follwing
  • No garbage charactors
  • No incomplete charactors
A
A
Connection with ADSL Modem : LL - 01188PA
1. Connect ethernet cable with ISP's ADSL modem directly.

2. Create Windows dial-up connection that ISP using PPPoE and type in User name and password

3. After finished, click "connect" button to connect the ISP

4. When verifying user name and password screen appears, the connection icon will go to System tray

Criteria : No system hang / system malfunction. Successful connectivity with the correct user name/password.



Note :
Perform all the tests in Battery Mode as much as possible (wherever applicable)
Perform this test in Admin mode and user mode in Windows XP/Windows 2000 and Windows NT
1. Update the EEPROM utility for Gigabit Ethernet and 10/100Mbps ethernet.
2. Install the correct driver for Gigabit ethernet and 10/100Mbps ethernet after updating EEPROM
3. Read Build Letter for procedure/restrictions.
4. Perform this test in Standlone and Docking station configuration.

Note : For testing PCI adapters, verify all the properties that comes with PCI driver/utilities.

1GB Ethernet Switch / Hub 3Com 3C16468 Superstack 10/100/1000 switch


Basic Gigabit Ethernet Verification

Test Item
LL-00930PA
Configuration
Win XP
Win 7
- Connect the system directly to 1Gbit hub/Switch
- Confirm the basic network functionality by file copy (300MB file size)
=> It should connect in 1Gbit (1000Mbps speed)
- Measure the file copy performance
Standalone
A
A
- Connect the system through Port replicator to 1Gbit hub/Switch
- Confirm the basic network functionality by file copy (300MB file size)
=> It should connect in 1Gbit (1000Mbps speed) if it is connected to 4 pair connector port replicator
=> It should connect in 10/100 Mbps if it is connected to 2 or 3 pair connector port replicator (old models)
- Measure the file copy performance
Port Replicator
(2/3 core connector)

Port Replicator
(4 core connector)
A
A
- Connect the system through Docking station to 1Gbit hub/Switch
- Confirm the basic network functionality by file copy (300MB file size)
=> It should connect in 1Gbit (1000Mbps speed) if it is connected to 4 pair connector docking station
=> It should connect in 10/100 Mbps if it is connected to 2 or 3 pair connector docking station (old models)
- Measure the file copy performance
Docking station
(2/3 core connector)

Docking station
(4 core connector)
A
A

Test Item
Configuration
Win XP
Win 7
Connect 1GB ethernet system to 1GB ethernet swich which in turn connected to server configured with 1GB ethernet adapter.
Perform Basic Network functions including File copy
Perform Suspend/Resume
Copy files of > 500MB size
Confirm that the file copy is completed without any error after resuming from suspend
Perform Hibernate/Resume
Copy files of > 500MB size
Confirm that the file copy is completed without any error after resuming from Hibernation
Standalone


Docking station
A
A
Performance
1. Copy file from server to client using 1GB network (File size : > 1GB single file)
2. Compare the performance with that of 10/100Mbps
3. Upload 1GB size file from client to server and measure the throughput.
Perform this test for both file copy and null copy
(Refer Reference procedure section for the performance details).
Standalone


Docking station
A
A
Perform the above tests when the settings in
Device Manager->Network adapters->select the adapter->Click properties->Advanced tab->Link speed & Duplex is set in
a) Auto Detect mode
b) Auto Negotiate 1000Mbps (applicable to Intel Gigabit Ethernet only)
Standalone


Docking station
A
A
PXE Boot behavior using PTE Server [LL-01433PA, LL-01424PA, LL-01423PA]


Attachment "4. iLab PTE User Guide.doc"can be seen at the bottom of the page.


Configure DHCP services in one server
Configure PXE boot services in another server.
Connect both to the same network with same subnet IP.

Server side:
1. Boot PTE Server
2. Launch VMware Workstation from Start > All Programs > VMware
3. Start the following Virtual Machines (VM) in order and wait until each VM has reached its login screen before powering on the next one:
a. Routers and Firewalls (any order)
- Router1
- Router2
- Router4
- Router-FW1
b. Top Level Domain Controller
- DC1 (Note: Manually login to DC1 and allow up to 1 minute after the login screen is available before logging in)
c. VMs dependent only on top level domain controller (any order)
- PKI-ACS
d. VMs dependent on PKI-ACS
- DC2
e. Everything else (any order)
- Altiris server
- AMT Tools
4. Check if the Virtual Machines boots successfully.
5. Go to DC1 (VM), click Start > All Programs > Administrative Tools > DHCP
6. Check if IPv4 has started.

Client side:
1. With Ethernet LAN cable, attach machine to Switch where Server is connected.
2. From PTE server, in DC1 Virtual Machine DHCP, check if the client machine's IP was listed.
3. Boot machine
4. Press F12 when Thinkpad Logo shows.
5. From Boot Menu, choose Realtek LAN adapter.
6. Machine will enter to PXE Boot. Will take 2-5 seconds.
7. Message should show with the following selections:

Please enter your desired boot image:

0 - local drives <defaults in 10 secs>
1 - DOS network boot list

PXE Boot behavior using PTE Server [LL-01433PA, LL-01424PA, LL-01423PA]

Test Item Criteria
With PXE Server and DHCP Server setup separately




Client side

1. With Ethernet LAN cable, attach client machine to switch were DHCP and PXE boot server was connected.
2. From DHCP server, check if the client machine's IP was listed.
3. Boot machine.
4. Press F12 when Thinkpad Logo shows.
5. From Boot Menu, choose Realtek LAN adapter.
6. Machine will enter to PXE Boot. Will take 2-5 seconds.

The following will show:

--------------------------------------------------------------------------------------------------------------------------------
Intel UNDI, PXE-2.1 (build 082)
Copyright (C) 1997-2000 Intel Corporation

This Product is covered by one or more of the following patents:
US5,307,459, US5,434,872, US5,732,094, US6,570,884, US6,115,776 and US6,327,625

Realtek PCI Express Gigabit Ethernet Controller Series v2.26 (090219)

CLIENT MAC ADDR : <client system's MAC Address> GUID : <client system's GUID>
CLIENT IP : 192.168.1.x MASK : 255.255.255.0 DHCP IP : 192.168.0.2
GATEWAY IP : 192.168.1.1

Downloaded WDSNBP . . .

Architecture : x64
Contacting Server : 192.168.0.2
TFTP Download : boot\x64\pxeboot.com

Press F12 for network service boot
--------------------------------------------------------------------------------------------------------------------------------

7. Press F12 upon showing the last message in PXE boot.
8. The system will automatically go to network service boot depending on the services loaded in Windows Deployment Services in PXE boot server.
9. The procedure below is an example:
9.1 In PXE boot server, Microsoft Windows Setup (x64) was loaded in Windows Deployment Services > Boot Images
9.2 The client system which is projected in the pictures below will show upon pressing F12 in step 7.





  • No error messages should show in client machine upon entering PXE boot.

Network stability test using Cross Over cable

Test Item Result
Configuration
Win XP
Win 7
Basic Functional Test
1. Attach USB 2.0 Ethernet Adapter with LAN cable to Test Machine 01 (with 3.0 USB Port).
2. Connect Machine 01 and Machine 02 with the cross cable.
3. Set a static IP on the test machines
.
IP:192.168.0.xxx

Subnetmask:255.255.255.0

Default Gateway:Non

4. Copy files from Machine 01 to Machine 02. And copy files from Machine 01 to Machine 02. (Perform on Machine 01.)

5. Confirm network stability and files were transferred successfully.
Standalone


USB Ethernet Cable

Docking station
Power Management
- Suspend (Fn+F4) the system x 10 times
- Confirm that the ethernet works fine after every suspend
- Hibernate(Fn+F12) the system x 10 times
- Confirm the functionality of ethernet network
- Start copying big files (>500MB)
- Press Fn+F3 x 10 times.
- Check that the file copy is not affected
Standalone


USB Ethernet Cable

Docking station

Merged from TC-3739PA
Win -7 32 bit
Win-7 64 bit
Network Diagnostics Framework (NDF)
  • To track and repair the connectivity issue, Windows Diagnostics dialog box now has a “Diagnose” button to provide more detailed information.

Open the Run window.
Type a non-existing server name.
Click the OK button.
Click the Diagnose button.


Expected results



SImilar kind of trials can be done for
1.Diagnose the failure when user misspells the share name
2. Correct server name but wrong share name
DHCPV6-DNS Interaction
  • In IPv6 network environment, multiple Domain Name System suffixes can be correctly covered. (This was broken without SP1.) (Example: yamato.ibm.com and ibm.com are both set and searched for IPv6 now.)

Pre-requisites or specific configuration for the scenario
DHCPV6 Stateful server joined to a domain (e.g., lhserver.com)
V6 scope configured (e.g. as 3ffe::)
Option 24 configured (e.g., as lhserver.com)

Step-by-step scenario description
Enable V6 stateful mode on the client.
Verify the output of ipconfig /all.
Note: The client should have the ipv6 address.
Verify that the configured domain (lhserver.com) appears in the DNS Suffix Search list, Connection -specific DNS suffix and Connection -specific DNS suffix search list.
From the test client machine, ping a dummy machine registered in the lhserver.com domain, e.g. ping dummy where dummy is the hostname of the dummy machine.
Note: You can verify this with the DNS packets captured using Netmon.

Expected results
The test client should try pinging it through dummy.lhserver.com and the ping request should succeed.
Single Sign on for Wired Networks
  • Single Sign On for wired network is supported and SSO can be checked in Event Viewer. (SSO for Wireless LAN was already supported.)

Scenario 1 – SSO over Wired:
The IT department requires that all wired devices require layer2 authentication (802.1X, WPA, WPA2) to succeed prior to access to the network. The IT admin configures the network to require user name/password access for both Winlogon Credentials as well as username password for authenticated network access. The user launches/opens the LogonUI, and is prompted for a single username and password. The user enters the credentials and is sequentially authenticated to the network and then the domain. The specific hardware requirement is a network that supports 802.1x authentication. The user must have a wired sso profile applied. See the Notes section below for a sample profile.

Apply an SSO wired profile.
Logoff/ Logon.
Check event logs to ensure sso occurred.

Scenario 2 - Change Password over SSO
A user’s network logon password has expired. When the user goes to logon to the network/machine a change password screen will be invoked, and the user will be able to change his/her sso logon password. No specific hardware requirement. The user must have a wired/wireless sso profile applied. See the Notes section below – A1 & A2 for a sample wired /wireless profile.

Ensure the user’s credentials is set to be expired.
Apply an SSO wired/wireless profile.
Logoff/Logon.
User should be prompted for a password changed for SSO credentials.
User should be able to change password successfully.


Scenario 3 - The ability to correct a wrong password entered for SSO
A user incorrectly enters his/her SSO network logon password. A screen to correct the user’s SSO password will be invoked, and the user will be given a chance to correct his/her SSO password. No specific hardware requirement. The user must have a wired/wireless sso profile applied. See the Notes section below-A1 & A2 for a sample wired /wireless profile.

Apply an SSO wired/wireless profile.
Logoff/Logon.
At the Logon screen enter the SSO password incorrectly.
The user should be prompted to correct his/her SSO password.
The user should be able to logon with the corrected SSO password.

OTHER DETAILS
EUT Quantity : One system 1. "Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead."
2. "Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case)"
(All Test Activity should be performed with AMT Enabled)
Adapter Name
Card Revision (Example 3B2....)
Firmware Version
10/100 Mbps Ethernet Phase Entry :
Phase Exit :
Phase Entry :
Phase Exit :
10/100/1000Mbps Etherent (1Gbit Ethernet) Phase Entry :
Phase Exit :
Phase Entry :
Phase Exit :



Fill out the following or attach the ATS system information file. Specify driver/EEPROM/firmware/card revision tested for Entry/Exit period.
Phase Entry :
Phase Exit :
EUT
BIOS
H8
Preload Image
Wireless Driver
Ethernet Driver details
EEPROM for Ethernet
Modem Driver
Audio
Video
ThinkPad Utility
Access Connections
Other driver details

TEMS Reviewer Log:09/13/2004 09:32:15 PM by Kazuo 1 Matsumoto/Japan/IBM (Review Comment: OK
Review Logs
Keywords:   None
Requirements :   None
Attached files :
4. iLab PTE User Guide.doc - 4. iLab PTE User Guide.doc (167936 bytes, ) 07/03/2015

Update History:
This document is not yet modified.