Test Case

Show / Hide direct link   <MAIN> 3192PA: EAPTLS Wireless Authentication Verification - PP-80411



Version 1.6
Created on 25/01/2006 18:49:51  by Muralidharan Seshadri
Summary
Preconditions
Status:   New
Priority:   Medium
BASIC INFORMATION
Section:S/W Test Require attachment:No
Team:Network Group:Basic Function
Lessons Learned:No Phase:FVT, SIV (BBFV), SIT
Locations:Inhouse: AWS and Cambridge, Inhouse: AWS, Inhouse: Cambridge, Compal, Flextronics, Quanta, Wistron Owned By:Eiji Ogata/LENOVO
Objective:To verify 802.1x/EAP-TLS authentications on Thinkpad for all supported WL adapters
CRITERIA
Successful EAP-TLS authentcation
No system malfunction/performance degradation
EUT QUANTITY
Two systems
EQUIPMENT
PPA Netowkring faciltiies.
Critical Attribute:[0] : WLS - Wireless

CONFIGURATION
REFERENCE PROCEDURE

802.1x Authentication Concept



Authentication Server
  • Install and Configure Windows 2003 Server or Windows 2000 Server with SP4 Patch as per the Enclosed Documentation


Attachment "1xdocs.zip"can be seen at the bottom of the page.



Attachment "80211corp.doc"can be seen at the bottom of the page.


Wireless Access Point
  • Update Latest Firmware (Vx Works / IOS) in Cisco AP 350 or Cisco 1200 AP.The Latest Firmware can be downloaded from the following Link;-

http://www.cisco.com/pcgi-bin/Software/WLAN/wlplanner.cgi
  • For 802.1x Configuration in Accespoint, follow the guidence in above attached Documentation
Wireless Client

Windows XP
  • The Wireless Driver shall be installed as per the approprite Build letter
  • Ensure Meetinghouse Supplicant shall be installed (Normally Installed during Installation of Wireless Driver)
  • Access Connection shall be installed as per build Letter

Windows 2K:

  • Minimum Service PACK 3 Shall be installed
  • QFE Patch Q313664 shall be installed

    or

  • SP4 shall have been installed.
  • Wireless Driver shall be installed as per the appropriate Build Letter
  • Ensure Meetinghouse Supplicant shall be installed (Normally Installed during Installation of Wireless Driver)
  • Access Connection shall be installed as per the Build Letter
  • Windows Wireless Configuration Service shall be in stopped state.
STATISTIC INFO
Operating System Win81-64bit Win81-32bit Win7- 64bit Win7- 32bit Total
Test Points
Duration
Workload
# Step actions Win81-64bitWin81-32bitWin7- 64bitWin7- 32bit
1 EAP-TLS Verification Authentication Matrix AAAA
2 EAP-TLS Authentication Client side Configuration and Verification AAAA
3 Network Reliability Test AAAA
DETAILS
ATTENTION!! Please follow below information.
1. Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead, then arrange to open defect, if needed.

2. Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case).

3. All Test Activity should be performed with AMT Enabled as Default (applicable on vPro enabled systems).

4. Please check Usability / Cosmetic issues (correct sentence/appropriate display/etc.) and open defect, if needed.

EAP-TLS Verification Authentication Matrix

Using Access Connections
Authentication
SSID
Authentication
Server
User Credential
Encryption
Intel
Realtek
Broadcomm
EAP-TLS
EAPTLSWEP
Win2003
Certificate
WEP
A
A
A
EAPTLSCKIP
Win2003
Certificate
CKIP
A
A
A
WPATLSTKIP
Win2003
Certificate
TKIP
A
A
A
WPATLSAES
Win2003
Certificate
AES
A
A
A
WPA2TLSAES
Win2003
Certificate
AES
A
A
A


Using Zero Config
Test Item
Configuration
Intel
Realtek
Broadcomm
EAP-TLS-WEP Verification
Standalone
A
A
A
WPA-TLS-TKIP Verification
Standalone
A
A
A
WPA-TLS-AES Verification
Standalone
A
A
A
WPA2-TLS-TKIP Verification
Standalone
A
A
A
WPA2-TLS-AES Verification
Standalone
A
A
A



EAP-TLS Authentication Client side Configuration and Verification


Perform the below test scenarios in both Admin and User modes

Test Item Check Item / Criteria
Configuration
Result
Win7 [32/64]
Win8 [32/64]
Wireless Client Configuration
  1. Make sure that Windows XP MS WPA Patch Q834565 is installed in the test system (SP2 will have this patch installed automatically)
  2. Connect the System to Wndows 2003 / Windows 2000 Domain Network by ethernet
  3. Register the Wireless Client as Domain Member of Windows 2003 /Windows 2000 Domain
  4. Add the Domain User to the Local Administrator group.
  5. Log in as the Domain user.
  6. Download Simple User Certificate using Internet Explorer or Microsoft Management Console from Certification Server in Windows 2003/ Windows 2000 Domain. (For ex: 192.168.21.1 /certsrv)
  7. After Certificate is successfully downloaded, from Internet Explorer, Click Tools>Internet options>content>certification and verify the downloaded certificate is listed. Click Advanced tab and select `Client Authentication` Box in Certificate purposes option.

  • The User Certificate shall be successfully downloaded
  • No Error Message while downloading the Certificate


Standalone
EAPTLSWEP
  1. Launch Access Connection application
  2. Assign Name as EAP-TLS , Choose the Network connection type as 'Wireless LAN (802.11)"
  3. Select the Wireless Adapter and click Next
  4. Type the SSID Name (For Ex.: EAP-AP). Set the following settings :-Connection Type :- Infrastructure and Wireless Mode : Auto (If applicable), In the WL Security Type, Choose the option `Use IEEE 802.1x Authentication` and Click Properties
  5. In `Enter your IEEE 802.1x Settings, Choose the following options:- Access Point Authentication : Open Data Encryption : WEP EAP Type : TLS
  6. Select Validate Server Certificate and Select the Certificate Issuer Name (For Example : WIFI)
  7. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : wifisvr.wifi.com)
  8. Check whether the option "Use Client certificate" is checked. and enter the Logon Name (For example : sankar@wifi.com)
  9. Click OK, Save and Apply the profile
  10. Verify IP Address is assigned by the DHCP Server after Authentication is successfull
  11. Check Network Connectivity by issuing Ping Command to Server
  12. Change the Data Encryption to "CKIP" in Step.5 and confirm steps 9 - 11
  13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.5 and confirm steps 9 - 11
  14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.5 and confirm steps 9 - 11
  15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.5 and confirm steps 9 - 11
  • Mutual Authentication of Server-Client and Client - Server shall happen
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Network Connectivity shall be available


Standalone
EAPTLS - With the option Validate Server Certificate unchecked and the Server details not entered
  1. Launch Access Connection application
  2. Assign Name as EAP-TLS , Choose the Network connection type as 'Wireless LAN (802.11)"
  3. Select the Wireless Adapter and click Next
  4. Type the SSID Name (For Ex.: EAP-AP). Set the following settings :-Connection Type :- Infrastructure and Wireless Mode : Auto (If applicable), In the WL Security Type, Choose the option `Use IEEE 802.1x Authentication` and Click Properties
  5. In `Enter your IEEE 802.1x Settings, Choose the following options:- Access Point Authentication : Open Data Encryption : WEP EAP Type : TLS
  6. Uncheck the box `Validate Server Certificate` option and Leave to the Default option of `Use Any Certificate Authority`
  7. Do Not enter any Server name or Domain Name
  8. Check the option Use Client certificateand enter the Logon Name (For example : sankar@wifi.com)
  9. Click OK, Save and Apply the profile
  10. Verify IP Address is assigned by the DHCP Server after Authentication is successfull
  11. Check Network Connectivity by issuing Ping Command to Server
  12. Change the Data Encryption to "CKIP" in Step.5 and confirm steps 9 - 11
  13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.5 and confirm steps 9 - 11
  14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.5 and confirm steps 9 - 11
  15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.5 and confirm steps 9 - 11
  • EAP-TLS authentication shall be successful with the options Validate Server Certificate unchecked and without the Server /Domain details
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Network Connectivity shall be available


Standalone
User switching with EAP-TLS (different user certificate)
  1. Log in admin mode.
  2. Install user certificate for admin mode.
  3. Create and apply a EAP-TLS profile.
  4. Make sure to allow all users to switch profiles option.
  5. Log off admin mode, log in to different user.
  6. Download and install user certificate for user mode.
  7. Connect the EAP-TLS profile.
  8. A pop-up message should appear prompting you to enter user credentials.
  9. Configure the profile for correct credentials, then apply.
  • Access Connections should prompt for user credentials after applying the EAP-TLS profile when switching from one user to another.
  • Connection should be established correct user credentials is selected.
  • Pop-up message will appear everytime switch user and apply profile


Standalone
User switching with EAP-TLS (same user certificate)
  1. Log in admin mode.
  2. Install user certificate for admin mode.
  3. Create and apply a EAP-TLS profile.
  4. Make sure to allow all users to switch profiles option.
  5. Log off admin mode, log in to different user.
  6. Install the same user certificate as in STEP 2 for user mode.
  7. Connect the EAP-TLS profile.
  8. Pop-up message should NOT appear.
  9. Configure the profile for correct credentials, then apply.
  • Access Connections should not prompt for user credentials after applying the WPA-TLS profile when switching from one user to another.
  • Connection should be established even without entering correct user credentials.
  • Pop-up message will not appear everytime switch user and apply profile


Standalone
Multiadapter EAP-TLS profile
1.. Configure multiadapter profile with EAP-TLS wireless setting
2. Download the user certificate for EAP-TLS profile
3. Cilck on connect for getting connected to this profile
4. Make sure "close all network connections when user logs off" is not checked in Global settings
5. Log in to the system with another user account which does not have user certificates


  • Connection should not be established
  • When manually connect the profile it will give a error message that user credentials required to connect to the network..


Standalone
EAP-TLS Single Adapter Profile with expired certificate installed
  1. Download and install the expired user certificate in the system.
  2. Open AC and create a EAPTLS profile
  3. Assign profile name as EAP-TLS , Choose the Network connection type as 'Wireless LAN (802.11)"
  4. Select the Wireless Adapter and click Next
  5. Type the SSID Name (For Ex.: EAP-AP). Set the following settings :-Connection Type :- Infrastructure and Wireless Mode : Auto (If applicable), In the WL Security Type, Choose the option `Use IEEE 802.1x Authentication` and Click Properties
  6. In `Enter your IEEE 802.1x Settings, Choose the following options:- Access Point Authentication : Open Data Encryption : WEP EAP Type : TLS
  7. Select Validate Server Certificate and Select the Certificate Issuer Name (For Example : WIFI)
  8. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : wifisvr.wifi.com)
  9. Check whether the option "Use Client certificate" is checked. and enter the Logon Name (For example : sankar@wifi.com)
  10. Click OK, Save and Apply the profile
  11. Confirm that the system fails to connect to the network.
  • Connection should not be established.
  • On Access Connections Diagnostics, make sure that the cause of connection failure is due to the expired certificate/wrong credentials.
EAP-TLS Multi Adapter Profile with expired certificate installed
  1. Download and install the expired user certificate in the system.
  2. Open AC and create a EAPTLS profile
  3. Assign profile name as EAP-TLS , Choose the Network connection type as 'Best Available Network"
  4. Select both Ethernet and Wireless adapters and click Next
  5. Type the SSID Name (For Ex.: EAP-AP). Set the following settings :-Connection Type :- Infrastructure and Wireless Mode : Auto (If applicable), In the WL Security Type, Choose the option `Use IEEE 802.1x Authentication` and Click Properties
  6. In `Enter your IEEE 802.1x Settings, Choose the following options:- Access Point Authentication : Open Data Encryption : WEP EAP Type : TLS
  7. Select Validate Server Certificate and Select the Certificate Issuer Name (For Example : WIFI)
  8. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : wifisvr.wifi.com)
  9. Check whether the option "Use Client certificate" is checked. and enter the Logon Name (For example : sankar@wifi.com)
  10. Click OK, Save and Apply the profile
  11. Confirm that the system fails to connect to the network.
  • Connection should not be established.
  • On Access Connections Diagnostics, make sure that the cause of connection failure is due to the expired certificate/wrong credentials.
EAP-TLS Single Adapter Profile with no certificate installed [UR-1352DS]
  1. DO NOT install the user certificate in the system.
  2. Open AC and create a EAPTLS profile
  3. Assign profile name as EAP-TLS , Choose the Network connection type as 'Wireless LAN (802.11)"
  4. Select the Wireless Adapter and click Next
  5. Type the SSID Name (For Ex.: EAP-AP). Set the following settings :-Connection Type :- Infrastructure and Wireless Mode : Auto (If applicable), In the WL Security Type, Choose the option `Use IEEE 802.1x Authentication` and Click Properties
  6. In 802.1x settings screen, click OK button with default condition and make sure popup msg (as defined in check item/criteria section) appears
  7. Click OK
  8. Uncheck the option "Use Client Certificate" and click OK.Make sure popup message appears
  9. Click OK
  10. Uncheck the option "Validate Server certificate" option and click OK. Make sure popup msg appears
  11. Click OK
  12. Confirm that profile is not allowed to save unless user certificate is installed in the system
  13. Click "Cancel" button and then click "Back" button
  14. Confirm that "Next" option is not grayedout

  • Make sure "No digital certificate was found.Verify that your digital certificate has been imported correctly" message appears when OK is clicked



Standalone
EAP-TLS Multi Adapter Profile with no certificate installed
  1. DO NOT install the user certificate in the system.
  2. Open AC and create a EAPTLS profile
  3. Assign profile name as EAP-TLS , Choose the Network connection type as 'Best Available Network"
  4. Select both Ethernet and Wireless adapters and click Next
  5. Type the SSID Name (For Ex.: EAP-AP). Set the following settings :-Connection Type :- Infrastructure and Wireless Mode : Auto (If applicable), In the WL Security Type, Choose the option `Use IEEE 802.1x Authentication` and Click Properties
  6. In 802.1x settings screen, click OK button with default condition and make sure popup msg (as defined in check item/criteria section) appears
  7. Click OK
  8. Uncheck the option "Use Client Certificate" and click OK.Make sure popup message appears
  9. Click OK
  10. Uncheck the option "Validate Server certificate" option and click OK. Make sure popup msg appears
  11. Click OK
  12. Confirm that profile is not allowed to save unless user certificate is installed in the system
  13. Click "Cancel" button and then click "Back" button
  14. Confirm that "Next" option is not grayedout
  • Make sure "No digital certificate was found.Verify that your digital certificate has been imported correctly" message appears
Standalone
Changing WL security setting from TLS to NOWEP: UR-01563DS
  1. Launch Access Connection application
  2. Assign Name as EAP-TLS , Choose the Network connection type as 'Wireless LAN (802.11)"
  3. Select the Wireless Adapter and click Next
  4. Type the SSID Name (For Ex.: EAP-AP). Set the following settings :-Connection Type :- Infrastructure and Wireless Mode : Auto (If applicable), In the WL Security Type, Choose the option `Use IEEE 802.1x Authentication` and Click Properties
  5. In `Enter your IEEE 802.1x Settings, Choose the following options:- Access Point Authentication : Open
  6. Data Encryption : WEP EAP Type : TLS
  7. Select Validate Server Certificate and Select the Certificate Issuer Name (For Example : WIFI)
  8. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : wifisvr.wifi.com)
  9. Check whether the option "Use Client certificate" is checked. and enter the Logon Name (For example : sankar@wifi.com)
  10. Click OK, Save and Apply the profile
  11. Verify IP Address is assigned by the DHCP Server after Authentication is successfull
  12. Check Network Connectivity by issuing Ping Command to Server
12. Now edit the profile and change the Wireless security type
to "None (encryption is disabled)" and give OK ===> Key
point
13. Connect the profile from Main GUI. Profile connects
successfully.
14. Check Network Connectivity by issuing Ping Command to
Server

CMVC # 83012 ==> XP/2K: Changing 802.1x to NOWEP doesnt refreshes AC Main GUI



1. Confirm the Security type in
AC Main GUI refreshes.



Standalone


Network Reliability Test

Test Item
Check Item / Criteria
Configuration
Result
Win7 [32/64]
Win8 [32/64]
Warm Boot Tests
  1. After Successfull authentication and Network Connection is established, Restart the System
  2. Login as Domain User and Check Wireless Connection is restored to the same 802.1x Profile used before restarting the system
  3. Repeat the steps 1-2 for 10 Times and verify the criteria.
  4. Network Connectivity shall be established after each Restart
  5. Network connection be restored to Previously used Profile unless AP is powered off

  • Authentication shall be successfull after each Restart
  • No Error Message after Restart

Access Connection Profile (Win8 NA)
Windows Zero Config
Connect /Disconnect Tests
  1. Launch Access Connection. Connect the Wireless Profile > EAP-TLS. Verify Authentication is successfull and Network Connection is established.
  2. Disconnect the Profile. Connect the same profile again.
  3. Verify Authentication is successfull and Network Connection is established.
  4. Repeat this operation in Step 1-2 for five times.

  • Authentication and NW connectivity shall be successfull after every Disconnect / Connect operation
  • No Error Message occurs

Access Connection Profile (Win8 NA)
Windows Zero Config
Cold Boot Tests
  1. After Successfull authentication and Network Connection is established, Shutdown the System
  2. Power On the system again
  3. Login as Domain User and Check Wireless Connection is restored to the same 802.1x Profile used before restarting the system
  4. Repeat the steps 1-3 for 10 Times and verify the criteria

  • Authentication shall be successfull after Cold Boot
  • Network Connectivity shall be established after each Restart
  • No Error Message occurs

Access Connection Profile (Win8 NA)
Windows Zero Config
Power Management Tests - UR2731
Suspend
  1. After Successfull authentication and Network Connection is established press Fn+F4 to suspend the system
  2. Resume the system by presing the Fn key after 1 minute.
  3. Ensure Authentication is successfull and Network Connectivity is restored to the previously connected AP /Network.
  4. Repeat Steps 1-3 for 10 times and verify the criteria

Hibernate
  1. After Successfull authentication and Network Connection is established press Fn+F12 to hibernate the system
  2. Resume the system by pressing the Power button after 1 minute.
  3. Ensure Authentication is successfull and Network Connectivity is restored to the previously connected AP /Network.
  4. Repeat Steps 1-3 for 10 times and verify the criteria

Lid-close
  1. After Successfull authentication and Network Connection is established close the lid to suspend the system
  2. Resume the system by opening the lid after 1 minute.
  3. Ensure Authentication is successfull and Network Connectivity is restored to the previously connected AP /Network.
  4. Repeat Steps 1-3 for 10 times and verify the criteria

(UR-03031AP)
Note: For Intel Wireless Cards in Windows 7 and Vista, Wireless profile authentication does not prompt even if "remember my user credentials" option is unchecked. This is working as designed using Intel Wireless LAN cards. (Ref:ECR83575, ECR86357)
  • Authentication shall be successfull after each PM
  • Network Connectivity shall be established after each PM
  • Network Connection shall not be available until the Windows Login is completed.
  • No Error Message occurs

Access Connection Profile (Win8 NA)
Windows Zero Config
Power Management Test with Logoff/Login
  1. Create a EAPTLS profileand apply
  2. Press Fn+F4 to suspend the system
  3. After 1 minute , resume the system . Make sure Network Connectivity is restored
  4. Logoff/Login the system and make sure Network Connectivity is restored
  5. Now again Press Fn+F4 to suspend the system
  6. After 1 minute , resume the system . Make sure Network Connectivity is restored

Note: For Intel Wireless Cards in Windows 7 and Vista, Wireless profile authentication does not prompt even if "remember my user credentials" option is unchecked. This is working as designed using Intel Wireless LAN cards. (Ref:ECR83575, ECR86357)

  • Authentication shall be successfull after each PM
  • Network Connectivity shall be established after each PM
  • No Error Message occurs

Access Connection Profile (Win8 NA)
Windows Zero Config
Power Management Test with Logoff/Login
Suspend
  1. Create an EAPTLS profile and apply
  2. Press Fn+F4 to suspend the system
  3. Resume the system by pressing Fn after 1 minute. Make sure Network Connectivity is restored.
  4. Logoff/Login the system and make sure Network Connectivity is restored.
  5. Now again press Fn+F4 to suspend the system
  6. Resume the system by pressing Fn after 1 minute. Make sure Network Connectivity is restored.

Hibernate
  1. Create an EAPTLS profile and apply
  2. Press Fn+F12 to hibernate the system
  3. Resume the system by pressing power button after 1 minute. Make sure Network Connectivity is restored.
  4. Logoff/Login the system and make sure Network Connectivity is restored.
  5. Now again press Fn+F12 to suspend the system
  6. Resume the system by pressing power after 1 minute. Make sure Network Connectivity is restored.

Lid-close
  1. Create an EAPTLS profile and apply
  2. Close the lid to suspend the system
  3. Resume the system by opening lid after 1 minute. Make sure Network Connectivity is restored.
  4. Logoff/Login the system and make sure Network Connectivity is restored.
  5. Now again close the lid to suspend the system
  6. Resume the system by opening lid after 1 minute. Make sure Network Connectivity is restored.

Note: For Intel Wireless Cards in Windows 7 and Vista, Wireless profile authentication does not prompt even if "remember my user credentials" option is unchecked. This is working as designed using Intel Wireless LAN cards. (Ref:ECR83575, ECR86357)

  • Authentication shall be successfull after each PM
  • Network Connectivity shall be established after each PM
  • No Error Message occurs

Access Connection Profile (Win8 NA)
Windows Zero Config
OTHER DETAILS
EUT Quantity : Two systems 1. "Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead."
2. "Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case)"
(All Test Activity should be performed with AMT Enabled) Note :
1. Perform the test in User mode as well as Administrator mode
2. Please check the version of Access Connection to be used for each product. Access Connection may require specific version of device driver to be installed for the adapters to be tested.
3. Refer latest Access Connection Function specification for the feature support.

Perform Access Connection on Japanese OS for SIT for the final verification. Initial stages of testing can be performed on US version. While doing JP coverage, verify the japanese characters, error messages and help menu contents.

Access Connections applications may have other functions/GUI not mentioned in this test case. Please verify all the available functions and GUI that comes with the particular version of Access Connections. Any updation required to the test case, Please inform Lenovo Engineers.



Known Limitations/Restrictions/Information
Known Limitations
1. For Intel Wireless Cards in Windows 7 and Vista, Wireless profile authentication does not prompt even if "remember my user credentials" option is unchecked. This is working as designed using Intel Wireless LAN cards. (Ref:ECR83575, ECR86357)
Restriction
1. Even "Allow all users of this system to create and apply loation profiles" Global settings option check box is checked, limited user account can not modify or create the setting for TCP/IP settings or security settings of local driver share, firewall settings due to Widnows security protection. Such setting is used with Windows default settings. Default is not checked.
2. Global settings can be only modified by the user when the logon privilege is administrator privilege.
3. The global settings option "Disable Adhoc connection type option in wireless LAN profiles" is not applicable, if the user create the profile using WIndows wireless LAN property window.
4. Profile disconnects when user change wireless security type of 802.1x peap to LEAP or vice versa
(Reference: ECR112851, W7:Profile disconnect when change wireless security type of 802.1x)
Information
1. When "Allow all users of this system to create and apply loation profiles" check box is checked, it allows user to create the location profiles and enables location switching regardless of the windows logon privilege (administrator or limited users).
2. Wireless profiles will be listed in the upper part of the profile list and the Ethernet profiles will be displayed at the lower part of the location profile list on "Automatic switching profile priority window". Due to the faster speed, the Ethernet profiles have higher priority than the wireless profiles.
3. Static IP address wireless profile will be listed in automtic location switching, as per the new design. However, static IP address ethernet profile will not be listed in automatic location switching.
4. ThinkPad 11b/g/n Wireless LAN Mini-PCI Express Adapter II has 1x2 antennas - 1 antenna for transmitter (Tx) and 2 antennas for receiver (Rx), and the maximum theoretical speed is 150Mbps (Tx) / 300Mbps (Rx) in the 802.11n mode. However, the current Realtek driver displays Tx speed as design. So it displays 150Mbps in the 802.11n mode even though the Rx speed is 300Mbps.
Solution : Display the Rx speed, instead of the Tx speed in the Realtek WLAN driver.


Summary of Results
Details
Intel
Realtek
Broadcom
Win7 [32/64]
Win8 [32/64]
Win7 [32/64]
Win8 [32/64]
Win7 [32/64]
Win8 [32/64]
Certificate Download and Client Configuration
EAPTLS-WEP/CKIP/WPATKIP/WPAAES/WPA2AES
Warm Boot Tests
Cold Boot Tests
Power Management Tests

TEMS Reviewer Log:
Review Logs
Keywords:   None
Requirements :   None
Attached files :
80211corp.doc - 80211corp.doc (138240 bytes, ) 07/03/2015
1xdocs.zip - 1xdocs.zip (417791 bytes, ) 07/03/2015

Update History:
This document is not yet modified.