Test Case

Show / Hide direct link   <MAIN> 3195PA: PEAPCHAP Wireless Authentication Verification - PP-80414



Version 1.7
Created on 25/01/2006 18:55:06  by Muralidharan Seshadri
Summary
Preconditions
Status:   New
Priority:   Medium
BASIC INFORMATION
Section:S/W Test Require attachment:No
Team:Network Group:Basic Function
Lessons Learned:No Phase:FVT, SIV (BBFV), SIT
Locations:Inhouse: AWS and Cambridge, Inhouse: AWS, Inhouse: Cambridge, Compal, Flextronics, Quanta, Wistron Owned By:Eiji Ogata/LENOVO
Objective:To verify all PEAP_CHAP authentications on ThinkPad for all supported WL adatpers
CRITERIA
Successful PEAP-CHAP authentications
No system malfunction/performance degradation
EUT QUANTITY
Two systems
EQUIPMENT
PA Networking facilities.
Critical Attribute:[0] : WLS - Wireless

CONFIGURATION
REFERENCE PROCEDURE
STATISTIC INFO
Operating System Win81-64bit Win81-32bit Win7- 64bit Win7- 32bit Total
Test Points
Duration
Workload
# Step actions Win81-64bitWin81-32bitWin7- 64bitWin7- 32bit
1 PEAP-CHAP Verification Authentication Matrix AAAA
2 Prompt for User Credentials Behavior for Access Connections AAAA
3 PEAP Authentication , Client side Configuration and Verification AAAA
4 CCX-5 AAAA
5 Network Reliability Test AAAA
DETAILS
ATTENTION!! Please follow below information.
1. Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead, then arrange to open defect, if needed.

2. Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case).

3. All Test Activity should be performed with AMT Enabled as Default (applicable on vPro enabled systems).

4. Please check Usability / Cosmetic issues (correct sentence/appropriate display/etc.) and open defect, if needed.

PEAP-CHAP Verification Authentication Matrix

Using Access Connections
Authentication
SSID
Authentication
Server
User Credential
Encryption
Intel
Realtek
Broadcom
PEAPCHAPV2
PEAPCHAP-WEP
Win2003
Windows Username & Password
WEP
A
A
A
Saved Username & Password
WEP
A
A
A
Temp Prompt Username & Password
WEP
A
A
A
PEAPCHAP-CKIP
Win2003
Windows Username & Password
CKIP
A
A
A
Saved Username & Password
CKIP
A
A
A
Temp Prompt Username & Password
CKIP
A
A
A
WPAPEAPCHAPTKIP
Win2003
Windows Username & Password
TKIP
A
A
A
Saved Username & Password
TKIP
A
A
A
Temp Prompt Username & Password
TKIP
A
A
A
WPAPEAPCHAPAES
Win2003
Windows Username & Password
AES
A
A
A
Saved Username & Password
AES
A
A
A
Temp Prompt Username & Password
AES
A
A
A
WP2APEAPCHAPAES
Win2003
Windows Username & Password
AES
A
A
A
Saved Username & Password
AES
A
A
A
Temp Prompt Username & Password
AES
A
A
A


Using Zero Config
Test Item
Configuration
Intel
Realtek
Broadcom
PEAP-MSCHAP/MSCHAPV2-WEP Verification
Standalone
A
A
A
WPA-PEAP MSCHAP/MSCHAPV2 - TKIP Verification
Standalone
A
A
A
WPA-PEAP MSCHAP/MSCHAPV2 - AES Verification
Standalone
A
A
A
WPA2-PEAP MSCHAP/MSCHAPV2 - TKIP Verification
Standalone
A
A
A
WPA2-PEAP MSCHAP/MSCHAPV2 - AES Verification
Standalone
A
A
A
CCKM Verification
Standalone
A
A
A

Prompt for User Credentials Behavior for Access Connections

GS - Global Settings option (Close all wireless network connections when user logs off.)
Yes - Prompt a Dialog Box
No- No Prompt


PEAP
Standby
Hibernate
Logon/Logoff
Restart
Disable (GS)
MSCHAP
No
No
No
Yes
Enable (GS)
MSCHAP
No
No
Yes
Yes



PEAP Authentication , Client side Configuration and Verification

Perform the below test scenarios in both Admin and User modes
Test Item
Check Item / Criteria
Configuration
Result
Win7 [32/64]
Win8 [32/64]
Wireless Client Configuration (Downloading Certificate)

1. Connect the System to Wndows 2003 / Windows 2000 Domain Network using Ethernet.
2. Register the Wireless Client as Domain Member of Windows 2003 /Windows 2000 Domain.
3. Add the Domain User to the Local Administrator group.
4. Log in as the Domain user.
5. Download & Install Root Certificate using Internet Explorer or Microsoft Management Console from Certification Server in Windows 2003/ Windows 2000 Domain. (For ex: 192.168.21.1 /certsrv)
6. Root CA Server Certificate needs to be stored by the following procedure:
- Start Certificate Import Wizard by clicking the Install Certificate button.
- Click "Next" and check at "Place all certificates in the following store".
- Click "Browse"and check at "Show physical stores".
- Explode at "Trusted Root Certification Authorities".
- Click "Local Computer" and then "Ok".
7. After Certificate is successfully installed , from Internet Explorer, Click
Tools => Internet options =>content => certificates
and verify the downloaded certificate is listed.
  • The Root Certificate shall be successfully downloaded
  • No Error Message while downloading the Certificate.
  • Verify that the downloaded certificate is listed in Internet Explorer Tools => Internet options =>content => certificates.


Standalone


A


A
PEAPCHAP Verification (Use saved user name and password)

1. Launch Access Connection application.
2. Create a PEAPCHAP profile with the following settings:
3. Select "Use IEEE 802.1x Authentication" --> Properties
4. Access Point Authentication : Open
Data Encryption: WEP
EAP Type: PEAP
Authentication protocol: MS-CHAP-V2
5. Click the option `Enter User Credentials`.
6. Enter the Roaming Identity/logon name
7. Choose the option `Use Saved user Name and password`, Enter the credentials and Click `Ok`.
8. Select Validate Server Certificate and Select the Certificate Issuer Name (For Example :CISCOAP).
9. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : eapsrv.eap.com) and give OK
10. Save and Apply the profile.
11. Check the Event Log of ACS Server and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
12. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 10-11
13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.4 and confirm steps 10-11
14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.4 and confirm steps 10-11
15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.4 and confirm steps 10-11

(UR#01654DS)
1. Install AC, Hotkey and Wireless Driver, restart the system.
2. Launch AC, Create and apply any 802.1x WL profile
3. After successful connection, disconnect the profile.
4. Edit the profile and change the wireless security type to WPAPSK,
Note: Don't enter User Settings

5. "Enter the WL Settings " Pop up apprs, Click OK
6. Change the WL security type back to 802.1x, Connect the profile in AC Main GUI
7. Pop-up message will appear saying " User credentials is required to connect to the Network"
8. Click OK to enter the user credentials.

Note:
Using Broadcom Walton WLAN adapter, WLAN driver just bypass all EAP packets to the supplicant. When using 801.x+WEP on Win764 bit machine, the MSFT PEAP-CHAP would try to grab the domain info, as the 802.1x was designed for domain. If the machine is in the domain, then it will work. Otherwise, the MSFT PEAP-CHAP would grab the machine name and append it to the username.

ECR68046, W7:Cannot connect PEAP-CHAP w/ Windows Username & Pwd [UR-2873]
  • Mutual Authentication of Server-Client and Client - Server shall happen
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Network Connectivity shall be available
  • Check the Access Point Event Log and Authentication is successfull.




















  • WL settings and user credentials should not be retained when WL security change from 802.1x to WPAPSK
Standalone































Standalone
A































A
A































A
PEAPCHAP Verification (In RELAX MODE - w/o selecting Validate Server Certificate)

(Use saved user name and password)
1. Launch Access Connection application.
2. Create a PEAPCHAP profile with the following settings:
3. Select "Use IEEE 802.1x Authentication" --> Properties
4. Access Point Authentication : Open
Data Encryption: WEP
EAP Type: PEAP
Authentication protocol: MS-CHAP-V2
5. Click the option `Enter User Credentials`.
6. Enter the Roaming Identity/logon name
7. Choose the option `Use Saved user Name and password`, Enter the credentials and Click `Ok`.
8. Uncheck the option Validate Server Certificate and Select the Certificate Issuer Name (For Example :CISCOAP).
9. Click next then apply profile.
10. Check the Event Log of ACS Server and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
11. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 9-10
13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.4 and confirm steps 9-10
14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.4 and confirm steps 9-10
15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.4 and confirm steps 9-10
  • The authentication shall be successful with the options Validate Server Certificate unchecked and without the Server /Domain details
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Network Connectivity shall be available
  • Check the Access Point Event Log and Authentication is successfull.
Standalone
A
A
PEAPCHAP Verification (Prompt temporary name and password)

1. Launch Access Connection application.
2. Create a PEAPCHAP profile with the following settings:
3. Select "Use IEEE 802.1x Authentication" --> Properties
4. Access Point Authentication : Open
Data Encryption: WEP
EAP Type: PEAP
Authentication protocol: MS-CHAP-V2
5. Click the option `Enter User Credentials`.
6. Enter the Roaming Identity/logon name
7. Choose the option `Prompt temporary name and password`and Click `Ok`.
8. Select Validate Server Certificate and Select the Certificate Issuer Name (For Example :CISCOAP).
9. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : eapsrv.eap.com) and give OK
10. Save and Apply the profile. Enter the correct credentials at the popup window.
11. Check the Event Log of ACS Server/Access Point and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
12. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 10-11
13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.4 and confirm steps 10-11
14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.4 and confirm steps 10-11
15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.4 and confirm steps 10-11
  • Mutual Authentication of Server-Client and Client - Server shall happen
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Network Connectivity shall be available
  • Check the Access Point Event Log and Authentication is successfull.
Standalone
A
A
PEAPCHAP Verification (In RELAX MODE - w/o selecting Validate Server Certificate)

(Prompt temporary name and password)
1. Launch Access Connection application.
2. Create a PEAPCHAP profile with the following settings:
3. Select "Use IEEE 802.1x Authentication" --> Properties
4. Access Point Authentication : Open
Data Encryption: WEP
EAP Type: PEAP
Authentication protocol: MS-CHAP-V2
5. Click the option `Enter User Credentials`.
6. Enter the Roaming Identity/logon name
7. Choose the option `Prompt temporary name and password`and Click `Ok`.
8. Uncheck the option Validate Server Certificate and Select the Certificate Issuer Name (For Example :CISCOAP).
9. Click next then apply profile.
10. Check the Event Log of ACS Server and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
11. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 9-10
13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.4 and confirm steps 9-10
14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.4 and confirm steps 9-10
15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.4 and confirm steps 9-10
  • The authentication shall be successful with the options Validate Server Certificate unchecked and without the Server /Domain details
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Network Connectivity shall be available
  • Check the Access Point Event Log and Authentication is successfull.
Standalone
A
A
PEAPCHAP Verification (Use Windows logon user name and password)

1. Launch Access Connection application.
2. Enable SSO Global Settings "Allow wireless connection at WIndows logon (requires system restart)" and restart the system.
3. Create a PEAPCHAP profile with the following settings:
4. Select "Use IEEE 802.1x Authentication" --> Properties
5. Access Point Authentication : Open
Data Encryption: WEP
EAP Type: PEAP
Authentication protocol: MS-CHAP-V2
6. Click the option `Enter User Credentials`.
7. Enter the Roaming Identity/logon name
8. Choose the option `Use Windows logon user name and password`, and click `Ok`.
9. Select Validate Server Certificate and Select the Certificate Issuer Name (For Example :CISCOAP).
10. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : PEAPCHAP) and give OK
11. Save and Apply the profile.
12. Check the Event Log of ACS Server and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
13. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 11-12
14. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.4 and confirm steps 11-12
15. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.4 and confirm steps 11-12
16. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.4 and confirm steps 11-12

Note:
Using Broadcom Walton WLAN adapter, WLAN driver just bypass all EAP packets to the supplicant. When using 801.x+WEP on Win764 bit machine, the MSFT PEAP-CHAP would try to grab the domain info, as the 802.1x was designed for domain. If the machine is in the domain, then it will work. Otherwise, the MSFT PEAP-CHAP would grab the machine name and append it to the username.

ECR68046, W7:Cannot connect PEAP-CHAP w/ Windows Username & Pwd
  • Mutual Authentication of Server-Client and Client - Server shall happen
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Network Connectivity shall be available
  • Check the Access Point Event Log and Authentication is successfull.
Standalone
A
A
PEAPCHAP Verification (In RELAX MODE - w/o selecting Validate Server Certificate)

(Use Windows logon user name and password)
1. Launch Access Connection application.
2. Enable SSO Global Settings "Allow wireless connection at WIndows logon (requires system restart)" and restart the system.
3. Create a PEAPCHAP profile with the following settings:
4. Select "Use IEEE 802.1x Authentication" --> Properties
5. Access Point Authentication : Open
Data Encryption: WEP
EAP Type: PEAP
Authentication protocol: MS-CHAP-V2
6. Click the option `Enter User Credentials`.
7. Enter the Roaming Identity/logon name
8. Choose the option `Use Windows logon user name and password`, and click `Ok`.
8. Uncheck the option Validate Server Certificate and Select the Certificate Issuer Name (For Example :CISCOAP).
9. Click next then apply profile.
10. Check the Event Log of ACS Server and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
11. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 9-10
13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.4 and confirm steps 9-10
14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.4 and confirm steps 9-10
15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.4 and confirm steps 9-10
  • The authentication shall be successful with the options Validate Server Certificate unchecked and without the Server /Domain details
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Network Connectivity shall be available
  • Check the Access Point Event Log and Authentication is successfull.
Standalone
A
A

CCX-5

PEAP PROFILE
Win7 [32/64]
Win8 [32/64]
MSCHAPV2
Prompt for Temporary Username and Password For suspend/resume scenario, user credential is cached so no prompt will be shown
For Log Off/Log On, prompt is dependent on the global setting option(Close all wireless network connections when user logs off). If it is enabled, it will prompt but if it is disabled, no prompt will show.
For restart, prompt is always shown
Windows User Name and Password This profile shows no prompt and is cached based on the windows login data
For suspend resume scenario, user credential is cached
Used Saved Username and Password For suspend/resume scenario, user credential is cached so no prompt will be shown
For Log Off/Log On, prompt is not shown
For restart, prompt is not shown


Network Reliability Test
Test Item Check Item / Criteria Configuration
Result
Win7 [32/64]
Win8 [32/64]
Warm Boot Tests
  1. After successful authentication and Network Connection is established, Restart the System
  2. Login as Domain User and Check Wireless Connection is restored to the same 802.1x Profile used before restarting the system
  3. Repeat the steps 1-2 for 10 Times and verify the criteria.
  4. Network Connectivity shall be established after each Restart
  5. Network connection be restored to Previously used Profile unless AP is powered off
  6. Network Connection shall not be available until the Windows Login is completed.

  • Authentication shall be successful after each Restart
  • No Error Message after Restart


Access Connection Profile (Win8 NA)
Windows Zero Config


A


A
Connect /Disconnect Tests
  1. Launch Access Connection. Connect the Wireless Profile > PEAPCHAP. Verify Authentication is successfull and Network Connection is established.
  2. Disconnect the Profile. Connect the same profile again.Verify Authentication is successful and Network Connection is established.
  3. Repeat this operation in Step 1-2 for five times.

  • Authentication shall be successfull after every Disconnect / Connect operation
  • Network Connectivity shall be established after every Disconnect / Connect operation
  • No Error Message occurs

Access Connection Profile (Win8 NA)
Windows Zero Config


A


A
Cold Boot Tests
  1. After successful authentication and Network Connection is established, Shutdown the System
  2. Power On the system again
  3. Login as Domain User and Check Wireless Connection is restored to the same 802.1x Profile used before restarting the system
  4. Repeat the steps 1-3 for 10 Times and verify the criteria

  • Authentication shall be successful after Cold Boot
  • Network Connectivity shall be established after each Restart
  • Network Connection shall not be available until the Windows Login is completed.
  • No Error Message occurs

Access Connection Profile (Win8 NA)
Windows Zero Config



A


A
Power Management Tests - UR-2729
Suspend
  1. After Successfull authentication and Network Connection is established press Fn+F4 to suspend the system
  2. Resume the system by presing the Fn key after 1 minute.
  3. Ensure Authentication is successfull and Network Connectivity is restored to the previously connected AP /Network.
  4. Repeat Steps 1-3 for 10 times and verify the criteria

Hibernate
  1. After successful authentication and Network Connection is established press Fn+F12 to hibernate the system
  2. Resume the system by presing the Power button after 1 minute.
  3. Ensure Authentication is successfull and Network Connectivity is restored to the previously connected AP /Network.
  4. Repeat Steps 1-3 for 10 times and verify the criteria

Lid-close
  1. After successful authentication and Network Connection is established close the lid to suspend the system
  2. Resume the system by opening the lid after 1 minute.
  3. Ensure Authentication is successful and Network Connectivity is restored to the previously connected AP /Network.
  4. Repeat Steps 1-3 for 10 times and verify the criteria

(UR-03034AP)
Note: For Intel Wireless Cards in Windows 7 and Vista, Wireless profile authentication does not prompt even if "remember my user credentials" option is unchecked. This is working as designed using Intel Wireless LAN cards. (Ref:ECR83575, ECR86357)
  • Authentication shall be successful after each PM
  • Network Connectivity shall be established after each PM
  • Network Connection shall not be available until the Windows Login is completed.
  • No Error Message occurs
Access Connection Profile (Win8 NA)
Windows Zero Config


A


A
Power Management Test with Logoff/Login
PEAPCHAP with "Prompt for Temporary username/password" option:

Suspend
  1. Create a PEAPCHAP profile with "Prompt for Temporary username/password" and apply, Press Fn+F4 to suspend the system.
  2. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again Press Fn+F4 to suspend the system.
  5. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.

Hibernate
  1. Create a PEAPCHAP profile with "Prompt for Temporary username/password" and apply, Press Fn+F12 to hibernate the system.
  2. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again Press Fn+F12 to suspend the system.
  5. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.

Lid-close
  1. Create a PEAPCHAP profile with "Prompt for Temporary username/password" and apply close the lid to suspend the system.
  2. Resume the system by opening the lid after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again close the lid to suspend the system.
  5. Resume the system by opening the lid after 1 minute. Make sure Network Connectivity is restored.

PEAPCHAP with "Saved Username and Password" option:

Suspend
  1. Create a PEAPCHAP profile with "Saved Username and Password" and apply, Press Fn+F4 to suspend the system.
  2. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again Press Fn+F4 to suspend the system.
  5. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.

Hibernate
  1. Create a PEAPCHAP profile with "Saved Username and Password" and apply, Press Fn+F12 to hibernate the system.
  2. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again Press Fn+F12 to suspend the system.
  5. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.

Lid-close
  1. Create a PEAPCHAP profile with "Saved Username and Password" and apply close the lid to suspend the system.
  2. Resume the system by opening the lid after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again close the lid to suspend the system.
  5. Resume the system by opening the lid after 1 minute. Make sure Network Connectivity is restored.

PEAPCHAP with SSO option :

Suspend
  1. Create a PEAPCHAP profile with SSO option and apply, Press Fn+F4 to suspend the system.
  2. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again Press Fn+F4 to suspend the system.
  5. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.

Hibernate
  1. Create a PEAPCHAP profile with SSO option and apply, Press Fn+F12 to hibernate the system.
  2. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again Press Fn+F12 to suspend the system.
  5. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.

Lid-close
  1. Create a PEAPCHAP profile with SSO option and apply close the lid to suspend the system.
  2. Resume the system by opening the lid after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again close the lid to suspend the system.
  5. Resume the system by opening the lid after 1 minute. Make sure Network Connectivity is restored.

Note: For Intel Wireless Cards in Windows 7 and Vista, Wireless profile authentication does not prompt even if "remember my user credentials" option is unchecked. This is working as designed using Intel Wireless LAN cards. (Ref:ECR83575, ECR86357)

  • Authentication shall be successfull after each PM
  • Network Connectivity shall be established after each PM
  • No Error Message occurs

Access Connection Profile (Win8 NA)
Windows Zero Config


A


A
OTHER DETAILS
EUT Quantity : Two systems 1. "Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead."
2. "Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case)"
(All Test Activity should be performed with AMT Enabled) Note :
1. Perform the test in User mode as well as Administrator mode
2. Please check the version of Access Connection to be used for each product. Access Connection may require specific version of device driver to be installed for the adapters to be tested.
3. Refer latest Access Connection Function specification for the feature support.

Perform Access Connection on Japanese OS for SIT for the final verification. Initial stages of testing can be performed on US version. While doing JP coverage, verify the japanese characters, error messages and help menu contents.

Access Connections applications may have other functions/GUI not mentioned in this test case. Please verify all the available functions and GUI that comes with the particular version of Access Connections. Any updation required to the test case, Please inform Lenovo Engineers.



Known Limitations/Restrictions/Information
Known Limitations
1. Note: For Intel Wireless Cards in Windows 7 and Vista, Wireless profile authentication does not prompt even if "remember my user credentials" option is unchecked. This is working as designed using Intel Wireless LAN cards. (Ref:ECR83575, ECR86357)
2. Windows will ask for user credentials prompt twice when connecting with 802.1 x PEAP. This is working as designed.
The first time, pop-up dialog to connect wifi. It cause by "WINLOGONEVENT_LOGON". But this time AC can not get valid ip, so connect fail. Then AC entered roaming processing, started second time connect and pop-up "username and password" dialog. If the machine can not get dhcp from server, the ip will not be got. So it will connect failed on first time.
(Ref. ECR112173, ECR112846, ECR112693)
Restriction
1. Even "Allow all users of this system to create and apply loation profiles" Global settings option check box is checked, limited user account can not modify or create the setting for TCP/IP settings or security settings of local driver share, firewall settings due to Widnows security protection. Such setting is used with Windows default settings. Default is not checked.
2. Global settings can be only modified by the user when the logon privilege is administrator privilege.
3. The global settings option "Disable Adhoc connection type option in wireless LAN profiles" is not applicable, if the user create the profile using WIndows wireless LAN property window.
4. Profile disconnects when user change wireless security type of 802.1x peap to LEAP or vice versa
(Reference: ECR112851, W7:Profile disconnect when change wireless security type of 802.1x)
Information
1. When "Allow all users of this system to create and apply loation profiles" check box is checked, it allows user to create the location profiles and enables location switching regardless of the windows logon privilege (administrator or limited users).
2. Wireless profiles will be listed in the upper part of the profile list and the Ethernet profiles will be displayed at the lower part of the location profile list on "Automatic switching profile priority window". Due to the faster speed, the Ethernet profiles have higher priority than the wireless profiles.
3. Static IP address wireless profile will be listed in automtic location switching, as per the new design. However, static IP address ethernet profile will not be listed in automatic location switching.
4. ThinkPad 11b/g/n Wireless LAN Mini-PCI Express Adapter II has 1x2 antennas - 1 antenna for transmitter (Tx) and 2 antennas for receiver (Rx), and the maximum theoretical speed is 150Mbps (Tx) / 300Mbps (Rx) in the 802.11n mode. However, the current Realtek driver displays Tx speed as design. So it displays 150Mbps in the 802.11n mode even though the Rx speed is 300Mbps.
Solution : Display the Rx speed, instead of the Tx speed in the Realtek WLAN driver.



Summary of Results
Details
Intel
Realtek
Broadcom
Win7 [32/64]
Win8 [32/64]
Win7 [32/64]
Win8 [32/64]
Win7 [32/64]
Win8 [32/64]
Certificate Download and Client Configuration
PEAPCHAP-WEP/CKIP/WPATKIP/WPAAES/WPA2AES Authentication using
- Use saved user name and password
PEAPCHAP-WEP/CKIP/WPATKIP/WPAAES/WPA2AES Authentication using
- Prompt temporary name and password
PEAPCHAP-WEP/CKIP/WPATKIP/WPAAES/WPA2AES Authentication using
- Use Windows logon user name and password
PEAPCHAP Verification
(In Relax Mode - w/o selecting Validate Server Certificate)
Network Reliability Tests
Power Management Tests

TEMS Reviewer Log:
Review Logs
Keywords:   None
Requirements :   None
Attached files :

Update History:
This document is not yet modified.