Test Case

Show / Hide direct link   <MAIN> 3197PA: EAPTTLS Wireless Authentication Verification - PP-80416



Version 1.7
Created on 25/01/2006 18:58:19  by Muralidharan Seshadri
Summary
Preconditions
Status:   New
Priority:   Medium
BASIC INFORMATION
Section:S/W Test Require attachment:No
Team:Network Group:Configuration
Lessons Learned:No Phase:FVT, SIV (BBFV), SIT
Locations:Inhouse: AWS and Cambridge, Inhouse: AWS, Inhouse: Cambridge, Compal, Flextronics, Quanta, Wistron Owned By:Eiji Ogata/LENOVO
Objective:To verify EAP-TTLS authentication on ThinkPad for all suported wireless adapters
CRITERIA
Successful EAP-TTLS authentications
No system malfunction/performance degradation
EUT QUANTITY
Two systems
EQUIPMENT
PA networking facilities
Critical Attribute:[0] : WLS - Wireless

CONFIGURATION
REFERENCE PROCEDURE




Details For Access Point and Client

SSID Name : EAP-TTLS

Access Connection Settings :-

Access Point Authentication : Open

Data Encryption : WEP


EAP Type : TTLS


Roaming Credentials : User Name (For Example jon)

Certificate Issuer : IBM Wireless Test Network
Server Name: EAPTTLSSVR.wireless.ibm.com

Root certificate: Please download the Root Certificate from PPA Hotload Server

STATISTIC INFO
Operating System Win81-64bit Win81-32bit Win7- 64bit Win7- 32bit Total
Test Points
Duration
Workload
# Step actions Win81-64bitWin81-32bitWin7- 64bitWin7- 32bit
1 EAPTTLS Verification Authentication Matrix AAAA
2 Prompt for User Credentials Behavior for Access Connections AAAA
3 EAP-TTLS Verification AAAA
4 CCX-5 AAAA
5 Network Reliability Test AAAA
DETAILS
ATTENTION!! Please follow below information.
1. Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead, then arrange to open defect, if needed.

2. Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case).

3. All Test Activity should be performed with AMT Enabled as Default (applicable on vPro enabled systems).

4. Please check Usability / Cosmetic issues (correct sentence/appropriate display/etc.) and open defect, if needed.

EAPTTLS Verification Authentication Matrix

Using Access Connections
Authentication
SSID
Authentication
Server
User Credential
Encryption
Intel
Realtek
Broadcomm
EAP-TTLS
EAP-TTLS-WEP
Funk Odyssey
Windows Username & Password
WEP
A
NA
A
Saved Username & Password
WEP
A
NA
A
Temp Prompt Username & Password
WEP
A
NA
A
EAP-TTLS-CKIP
Funk Odyssey
Windows Username & Password
CKIP
A
NA
A
Saved Username & Password
CKIP
A
NA
A
Temp Prompt Username & Password
CKIP
A
NA
A
WPAEAPTTLSTKIP
Funk Odyssey
Windows Username & Password
TKIP
A
NA
A
Saved Username & Password
TKIP
A
NA
A
Temp Prompt Username & Password
TKIP
A
NA
A
WPAEAPTTLSAES
Funk Odyssey
Windows Username & Password
AES
A
NA
A
Saved Username & Password
AES
A
NA
A
Temp Prompt Username & Password
AES
A
NA
A
WPA2EAPTTLSAES
Funk Odyssey
Windows Username & Password
AES
A
NA
A
Saved Username & Password
AES
A
NA
A
Temp Prompt Username & Password
AES
A
NA
A


Using Zero Config
Test Item
Configuration
Intel
Realtek
Broadcomm
EAP-TTLS-WEP Verification
Standalone
A
NA
A
WPA-TTLS-TKIP Verification
Standalone
A
NA
A
WPA-TTLS-AES Verification
Standalone
A
NA
A
WPA2-TTLS-TKIP Verification
Standalone
A
NA
A
WPA2-TTLS-AES Verification
Standalone
A
NA
A
CCKM Verification
Standalone
A
NA
A

Prompt for User Credentials Behavior for Access Connections

GS - Global Settings option (Close all wireless network connections when user logs off.)
Yes - Prompt a Dialog Box
No- No Prompt

EAPTTLS
Standby
Hibernate
Logon/Logoff
Restart
Disable (GS)
Manual Prompt
No
No
No
Yes
Enable (GS)
Manual Prompt
No
No
Yes
Yes


EAP-TTLS Verification

Perform the below test scenarios in both Admin and User modes
Test Item
Check Item / Criteria
Configuration
Result
Win7 [32/64]
Win8 [32/64]
Wireless Client Configuration.
(Downloading Certificate)
  1. Make sure that Windows XP MS WPA Patch Q834565 is installed in the test system (Applicable only for Win XP SP1. This is included in XP-SP2)
  2. Connect the System to Wndows 2003 / Windows 2000 Domain Network by ethernet
  3. Register the Wireless Client as Domain Member of Windows 2003 /Windows 2000 Domain
  4. Add the Domain User to the Local Administrator group.
  5. Log in as the Domain user.
  6. Download Root Certificate using Internet Explorer or Microsoft Management Console from Certification Server in Windows 2003/ Windows 2000 Domain. (For ex: 192.168.51.1 /certsrv)
  7. Install the Root Certificate
    - Root CA Server Certificate needs to be stored by the following procedure:
    1. Start Certificate Import Wizard by clicking the Install Certificate button.
    2. Click "Next" and check at "Place all certificates in the following store"
    3. Click "Browse"and check at "Show physical stores"
    4. Explode at "Trusted Root Certification Authorities"
    5. Click "Local Computer" and then "Ok"
8. After Certificate is successfully installed , from Internet
Explorer, Click Tools>Internet options>content>
certification and verify the downloaded certificate is listed.
  • The User Certificate shall be successfully downloaded
  • No Error Message while downloading the Certificate
Stand alone
A
EAP-TTLS (Use Saved Username and Password)
  1. Launch Access Connection application and create a EAP-TTLS profile
  2. Create a EAP-TTLS profile with the following settings
  3. Select "Use IEEE 802.1x Authentication" --> Properties
  4. Access Point Authentication : Open Data Encryption : WEP EAP Type : TTLS
  5. In the Authentication protocol -->Choose MS-CHAP-V2
  6. Enter User Credentials (Used Saved Username and Password)
  7. Select Validate Server Certificate and Select the Certificate Issuer Name
  8. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (Forexample:EAPTTLS.wireless.ibm.com)
  9. Click Next , Save and Apply the profile
  10. Verify IP Address is assigned by the DHCP Server after Authentication is successfull
  11. Check Network Connectivity by issuing Ping Command to Server
  12. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 9 - 11
  13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.4 and confirm steps 9 - 11
  14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.4 and confirm steps 9 - 11
  15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.4 and confirm steps 9 - 11
  • Mutual Authentication of Server-Client and Client - Server shall happen
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Make sure that the maximum characters that is allowed for both username and password fields is 50
Stand alone
A
EAP-TTLS(Use Windows log on username and password)
  1. Launch Access Connection application and create a EAP-TTLS profile
  2. Create a EAP-TTLS profile with the following settings
  3. Select "Use IEEE 802.1x Authentication" --> Properties
  4. Access Point Authentication : Open Data Encryption : WEP EAP Type : TTLS
  5. In the Authentication protocol -->Choose MS-CHAP-V2
  6. Enter User Credentials (Use Windows logon username and password)
  7. Select Validate Server Certificate and Select the Certificate Issuer Name
  8. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (Forexample:EAPTTLS.wireless.ibm.com)
  9. Click Next , Save and Apply the profile
  10. Verify IP Address is assigned by the DHCP Server after Authentication is successfull
  11. Check Network Connectivity by issuing Ping Command to Server
  12. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 9 - 11
  13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.4 and confirm steps 9 - 11
  14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.4 and confirm steps 9 - 11
  15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.4 and confirm steps 9 - 11
  • Mutual Authentication of Server-Client and Client - Server shall happen
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Network Connectivity shall be available
  • Make sure that the maximum characters that is allowed for both username and password fields is 50
Stand alone
A
EAP-TTLS (Prompt Temporary name and Password)
  1. Launch Access Connection application and create a EAP-TTLS profile
  2. Create a EAP-TTLS profile with the following settings
  3. Select "Use IEEE 802.1x Authentication" --> Properties
  4. Access Point Authentication : Open Data Encryption : WEP EAP Type : TTLS
  5. In the Authentication protocol -->Choose MS-CHAP-V2
  6. Enter User Credentials (Prompt temporary name and password)
  7. Select Validate Server Certificate and Select the Certificate Issuer Name
  8. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (Forexample:EAPTTLS.wireless.ibm.com)
  9. Click Next , Save and Apply the profile
  10. Verify IP Address is assigned by the DHCP Server after Authentication is successfull
  11. Check Network Connectivity by issuing Ping Command to Server
  12. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 9 - 11
  13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.4 and confirm steps 9 - 11
  14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.4 and confirm steps 9 - 11
  15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.4 and confirm steps 9 - 11
  • Mutual Authentication of Server-Client and Client - Server shall happen
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Network Connectivity shall be available
  • Make sure that the maximum characters that is allowed for both username and password fields is 50
Stand alone
A
EAP-TTLS Single Adapter Profile with expired certificate installed - UR-2732
  1. Download and install the expired user certificate in the system.
  2. Open AC and create a EAPTTLS profile
  3. Assign profile name as EAP-TTLS , Choose the Network connection type as 'Wireless LAN (802.11)"
  4. Select the Wireless Adapter and click Next
  5. Type the SSID Name (For Ex.: EAP-AP). Set the following settings :-Connection Type :- Infrastructure and Wireless Mode : Auto (If applicable), In the WL Security Type, Choose the option `Use IEEE 802.1x Authentication` and Click Properties
  6. In `Enter your IEEE 802.1x Settings, Choose the following options:- Access Point Authentication : Open Data Encryption : WEP EAP Type : TTLS
  7. Select Validate Server Certificate and Select the Certificate Issuer Name
  8. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : EAPTTLS.wireless.ibm.com)
  9. Check whether the option "Use Client certificate" is checked. and enter the Logon Name (For example : sankar@wifi.com)
  10. Click OK, Save and Apply the profile
  11. Confirm that the system fails to connect to the network.
  • Connection should not be established.
  • On Access Connections Diagnostics, make sure that the cause of connection failure is due to the expired certificate/wrong credentials.
EAP-TTLS Multi Adapter Profile with expired certificate installed
  1. Download and install the expired user certificate in the system.
  2. Open AC and create a EAPTTLS profile
  3. Assign profile name as EAP-TTLS , Choose the Network connection type as 'Best Available Network"
  4. Select both Ethernet and Wireless adapters and click Next
  5. Type the SSID Name (For Ex.: EAP-AP). Set the following settings :-Connection Type :- Infrastructure and Wireless Mode : Auto (If applicable), In the WL Security Type, Choose the option `Use IEEE 802.1x Authentication` and Click Properties
  6. In `Enter your IEEE 802.1x Settings, Choose the following options:- Access Point Authentication : Open Data Encryption : WEP EAP Type : TTLS
  7. Select Validate Server Certificate and Select the Certificate Issuer Name
  8. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : EAPTTLS.wireless.ibm.com)
  9. Check whether the option "Use Client certificate" is checked. and enter the Logon Name (For example : sankar@wifi.com)
  10. Click OK, Save and Apply the profile
  11. Confirm that the system fails to connect to the network.
  • Connection should not be established.
  • On Access Connections Diagnostics, make sure that the cause of connection failure is due to the expired certificate/wrong credentials.
Changing WL security setting from EAP-TTLS to NOWEP: UR-01568DS
  1. Launch Access Connection application
  2. Assign Name as EAP-TTLS , Choose the Network connection type as 'Wireless LAN (802.11)"
  3. Select the Wireless Adapter and click Next
  4. Type the SSID Name (For Ex.: EAP-AP). Set the following settings :-Connection Type :- Infrastructure and Wireless Mode : Auto (If applicable), In the WL Security Type, Choose the option `Use IEEE 802.1x Authentication` and Click Properties
  5. In `Enter your IEEE 802.1x Settings, Choose the following options:- Access Point Authentication : Open Data Encryption : WEP EAP Type : TTLS
  6. Select Validate Server Certificate and Select the Certificate Issuer Name (For Example : WIFI)
  7. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : wifisvr.wifi.com)
  8. Check whether the option "Use Client certificate" is checked. and enter the Logon Name (For example : sankar@wifi.com)
  9. Click OK, Save and Apply the profile
  10. Verify IP Address is assigned by the DHCP Server after Authentication is successfull
  11. Check Network Connectivity by issuing Ping Command to Server
12. Now edit the profile and change the Wireless security type
to "None (encryption is disabled)" and give OK ===> Key
point
13. Connect the profile from Main GUI. Profile connects
successfully.
14. Check Network Connectivity by issuing Ping Command to
Server

CMVC # 83012 ==> XP/2K: Changing 802.1x to NOWEP doesnt refreshes AC Main GUI


1. Confirm the Security type in
AC Main GUI refreshes.


Standalone
EAP-TTLS with Validate Server Certificate Unchecked
  1. Launch Access Connection application and create a EAP-TTLS profile
  2. Create a EAP-TTLS profile with the following settings
  3. Select "Use IEEE 802.1x Authentication" --> Properties
  4. Access Point Authentication : Open Data Encryption : WEP EAP Type : TTLS
  5. In the Authentication protocol -->Choose MS-CHAP-V2
  6. Enter User Credentials (Use Saved Username and Password)
  7. Uncheck the option "Validate Server Certificate"
  8. Click Next , Save and Apply the profile
  9. Verify IP Address is assigned by the DHCP Server after Authentication is successfull
  10. Check Network Connectivity by issuing Ping Command to Server
  11. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 9 - 11
  12. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.4 and confirm steps 9 - 11
  13. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.4 and confirm steps 9 - 11
  14. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.4 and confirm steps 9 - 11
  15. Perform the same operation for EAPTTLS with "Prompt username and password"
  16. Perform the same operation for EAPTTLS with "Use windows logon username and password"


EAP-TTLS PAP (Use Saved Username and Password) - UR-1752DS
  1. Launch Access Connection application and create a EAP-TTLS profile
  2. Create a EAP-TTLS profile with the following settings
  3. Select "Use IEEE 802.1x Authentication" --> Properties
  4. Access Point Authentication : Open Data Encryption : WEP EAP Type : TTLS
  5. In the Authentication protocol -->Choose PAP
  6. Enter User Credentials (Used Saved Username and Password)
  7. Select Validate Server Certificate and Select the Certificate Issuer Name
  8. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (Forexample:EAPTTLS.wireless.ibm.com)
  9. Click Next , Save and Apply the profile
  10. Verify IP Address is assigned by the DHCP Server after Authentication is successfull
  11. Check Network Connectivity by issuing Ping Command to Server
  12. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 9 - 11
  13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.4 and confirm steps 9 - 11
  14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.4 and confirm steps 9 - 11
  15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.4 and confirm steps 9 - 11

Note: Make Sure like MSCHAP, PAP Authentication should get connected with Prompt for temporary name and password, user window logon with/without validate server certificate.
  • Mutual Authentication of Server-Client and Client - Server shall happen
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Network Connectivity shall be available
  • Make sure that the maximum characters that is allowed for both username and password fields is 50

  • Mutual Authentication of Server-Client and Client - Server shall happen
  • No Error Message related to authentication failure shall occur.
  • IP Address shall be assigned by DHCP Server
  • Make sure that the maximum characters that is allowed for both username and password fields is 50

Stand alone
































Stand alone




A
































A

CCX-5

TTLS
WinXP
Win7 [32/64]
Win8 [32/64]
Prompt for Temporary Username and Password For suspend/resume scenario, user credential is cached so no prompt will be shown
For Log Off/Log On, prompt is dependent on the global setting option(Close all wireless network connections when user logs off). If it is enabled, it will prompt but if it is disabled, no prompt will show.
For restart, prompt is always shown
Windows User Name and Password This profile shows no prompt and is cached based on the windows login data
For suspend resume scenario, user credential is cached
Used Saved Username and Password For suspend/resume scenario, user credential is cached so no prompt will be shown
For Log Off/Log On, prompt is not shown
For restart, prompt is not shown

Network Reliability Test

Test Item
Check Item / Criteria
Configuration
Win7 [32/64]
Win8 [32/64]
Warm Boot Tests
  1. After Successfull authentication and Network Connection is established, Restart the System
  2. Login as Domain User and Check Wireless Connection is restored to the same 802.1x Profile used before restarting the system
  3. Repeat the steps 1-2 for 10 Times and verify the criteria.
  4. If any error Message is found during Reboot operation, Please report this problem
  • Authentication shall be successfull after each Restart
  • Network Connectivity shall be established after each Restart
  • Network connection be restored to Previously used Profile unless AP is powered off
  • No Error Message after Restart

Access Connection Profile (Win8 NA)
Windows Zero Config

A

Cold Boot Tests
  1. After Successfull authentication and Network Connection is established, Shutdown the System
  2. Power On the system again
  3. Login as Domain User and Check Wireless Connection is restored to the same 802.1x Profile used before restarting the system
  4. Repeat the steps 1-3 for 10 Times and verify the criteria
  • Authentication shall be successfull after Cold Boot
  • Network Connectivity shall be established after each Restart
  • No Error Message occurs

Access Connection Profile (Win8 NA)
Windows Zero Config

A

Power Management Tests - UR-2732
Suspend
  1. After Successfull authentication and Network Connection is established press Fn+F4 to suspend the system
  2. Resume the system by presing the Fn key after 1 minute.
  3. Ensure Authentication is successfull and Network Connectivity is restored to the previously connected AP /Network.
  4. Repeat Steps 1-3 for 10 times and verify the criteria

Hibernate
  1. After Successfull authentication and Network Connection is established press Fn+F12 to hibernate the system
  2. Resume the system by presing the Power button after 1 minute.
  3. Ensure Authentication is successfull and Network Connectivity is restored to the previously connected AP /Network.
  4. Repeat Steps 1-3 for 10 times and verify the criteria

Lid-close
  1. After Successfull authentication and Network Connection is established close the lid to suspend the system
  2. Resume the system by opening the lid after 1 minute.
  3. Ensure Authentication is successfull and Network Connectivity is restored to the previously connected AP /Network.
  4. Repeat Steps 1-3 for 10 times and verify the criteria

(UR-03032AP)
Note: For Intel Wireless Cards in Windows 7 and Vista, Wireless profile authentication does not prompt even if "remember my user credentials" option is unchecked. This is working as designed using Intel Wireless LAN cards. (Ref:ECR83575, ECR86357)
  • Authentication shall be successfull after each PM
  • Network Connectivity shall be established after each PM
  • Network Connection shall not be available until the Windows Login is completed.
  • No Error Message occurs

Access Connection Profile (Win8 NA)
Windows Zero Config
Power Management Test with Logoff/Login
PEAPGTC with "Prompt for Temporary username/password" option:

Suspend
  1. Create a PEAPGTC profile with "Prompt for Temporary username/password" and apply, Press Fn+F4 to suspend the system.
  2. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again Press Fn+F4 to suspend the system.
  5. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.

Hibernate
  1. Create a PEAPGTC profile with "Prompt for Temporary username/password" and apply, Press Fn+F12 to hibernate the system.
  2. Resume the system by pressing the Power button after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again Press Fn+F12 to suspend the system.
  5. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.

Lid-close
  1. Create a PEAPGTC profile with "Prompt for Temporary username/password" and apply close the lid to suspend the system.
  2. Resume the system by opening the lid after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again close the lid to suspend the system.
  5. Resume the system by opening the lid after 1 minute. Make sure Network Connectivity is restored.

PEAPGTC with "Saved Username and Password" option:

Suspend
  1. Create a PEAPGTC profile with "Saved Username and Password" and apply, Press Fn+F4 to suspend the system.
  2. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again Press Fn+F4 to suspend the system.
  5. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.

Hibernate
  1. Create a EAPTTLS profile with "Saved Username and Password" and apply, Press Fn+F12 to hibernate the system.
  2. Resume the system by pressing the Power button after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again Press Fn+F12 to suspend the system.
  5. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.

Lid-close
  1. Create a EAPTTLS profile with "Saved Username and Password" and apply close the lid to suspend the system.
  2. Resume the system by opening the lid after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again close the lid to suspend the system.
  5. Resume the system by opening the lid after 1 minute. Make sure Network Connectivity is restored.

EAPTTLS with SSO option :

Suspend
  1. Create a EAPTTLS profile with SSO option and apply, Press Fn+F4 to suspend the system.
  2. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again Press Fn+F4 to suspend the system.
  5. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.

Hibernate
  1. Create a EAPTTLS profile with SSO option and apply, Press Fn+F12 to hibernate the system.
  2. Resume the system by pressing the Power button after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again Press Fn+F12 to suspend the system.
  5. Resume the system by pressing the Fn key after 1 minute. Make sure Network Connectivity is restored.

Lid-close
  1. Create a EAPTTLS profile with SSO option and apply close the lid to suspend the system.
  2. Resume the system by opening the lid after 1 minute. Make sure Network Connectivity is restored.
  3. Logoff/Login the system and make sure Network Connectivity is restored
  4. Now again close the lid to suspend the system.
  5. Resume the system by opening the lid after 1 minute. Make sure Network Connectivity is restored.

Note: For Intel Wireless Cards in Windows 7 and Vista, Wireless profile authentication does not prompt even if "remember my user credentials" option is unchecked. This is working as designed using Intel Wireless LAN cards. (Ref:ECR83575, ECR86357)

  • Authentication shall be successfull after each PM
  • Network Connectivity shall be established after each PM
  • No Error Message occurs

Access Connection Profile (Win8 NA)
Windows Zero Config

A
OTHER DETAILS
EUT Quantity : Two systems 1. "Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead."
2. "Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case)"
(All Test Activity should be performed with AMT Enabled) "Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case)"

RESULT
Copy this section into the RESULT section of your report.


Note :
1. Perform the test in User mode as well as Administrator mode
2. Please check the version of Access Connection to be used for each product. Access Connection may require specific version of device driver to be installed for the adapters to be tested.
3. Refer latest Access Connection Function specification for the feature support.

Perform Access Connection on Japanese OS for SIT for the final verification. Initial stages of testing can be performed on US version. While doing JP coverage, verify the japanese characters, error messages and help menu contents.

Access Connections applications may have other functions/GUI not mentioned in this test case. Please verify all the available functions and GUI that comes with the particular version of Access Connections. Any updation required to the test case, Please inform Lenovo Engineers.



Known Limitations/Restrictions/Information
Known Limitations
1. For Intel Wireless Cards in Windows 7 and Vista, Wireless profile authentication does not prompt even if "remember my user credentials" option is unchecked. This is working as designed using Intel Wireless LAN cards. (Ref:ECR83575, ECR86357)
2. EAP-TTLS authentication is not supported on Windows 7/Vista for Realtek (Stockton, Rush) and Broadcom (Walton) WLAN cards. - UR-2797
Reference: ECR66561 W7:EAP-TTLS option not available using Stockton, ECR66420 W7/VIS:EAP-TTLS option not available using Walton
Restriction
1. Even "Allow all users of this system to create and apply loation profiles" Global settings option check box is checked, limited user account can not modify or create the setting for TCP/IP settings or security settings of local driver share, firewall settings due to Widnows security protection. Such setting is used with Windows default settings. Default is not checked.
2. Global settings can be only modified by the user when the logon privilege is administrator privilege.
3. The global settings option "Disable Adhoc connection type option in wireless LAN profiles" is not applicable, if the user create the profile using WIndows wireless LAN property window.
4. Profile disconnects when user change wireless security type of 802.1x peap to LEAP or vice versa
(Reference: ECR112851, W7:Profile disconnect when change wireless security type of 802.1x)
Information
1. When "Allow all users of this system to create and apply loation profiles" check box is checked, it allows user to create the location profiles and enables location switching regardless of the windows logon privilege (administrator or limited users).
2. Wireless profiles will be listed in the upper part of the profile list and the Ethernet profiles will be displayed at the lower part of the location profile list on "Automatic switching profile priority window". Due to the faster speed, the Ethernet profiles have higher priority than the wireless profiles.
3. Static IP address wireless profile will be listed in automtic location switching, as per the new design. However, static IP address ethernet profile will not be listed in automatic location switching.
4. ThinkPad 11b/g/n Wireless LAN Mini-PCI Express Adapter II has 1x2 antennas - 1 antenna for transmitter (Tx) and 2 antennas for receiver (Rx), and the maximum theoretical speed is 150Mbps (Tx) / 300Mbps (Rx) in the 802.11n mode. However, the current Realtek driver displays Tx speed as design. So it displays 150Mbps in the 802.11n mode even though the Rx speed is 300Mbps.
Solution : Display the Rx speed, instead of the Tx speed in the Realtek WLAN driver


Summary of Results

Details
Intel
Realtek
Broadcom
Win7 [32/64]
Win8 [32/64]
Win7 [32/64]
Win8 [32/64]
Win7 [32/64]
Win8 [32/64]
Certificate Download and Client Configuration
EAPTTLS-WEP/CKIP/WPATKIP/WPAAES/WPA2AES (Saved Username and Password)
EAPTTLS-WEP/CKIP/WPATKIP/WPAAES/WPA2AES (Use windows logon username and password)
EAPTTLS-WEP/CKIP/WPATKIP/WPAAES/WPA2AES (Prompt temporary name and password)
EAPTTLS-WEP/CKIP/WPATKIP/WPAAES/WPA2AES - Verification with disable Validate Server Certificate
EAPTTLS with Power Management

TEMS Reviewer Log:
Review Logs
Keywords:   None
Requirements :   None
Attached files :

Update History:
This document is not yet modified.