Test Case

Show / Hide direct link   <MAIN> 3201PA: User Scenerio Test - PP-80479



Version 1.1
Created on 25/01/2006 19:07:06  by Muralidharan Seshadri
Summary
Preconditions
Status:   New
Priority:   Medium
BASIC INFORMATION
Section:S/W Test Require attachment:No
Team:Network Group:Usability
Lessons Learned:No Phase:FVT, SIV (BBFV), SIT
Locations:Inhouse: AWS and Cambridge, Inhouse: AWS, Inhouse: Cambridge, Compal, Flextronics, Quanta, Wistron Owned By:Eiji Ogata/LENOVO
Objective:To verify the user scenerio functions using Wireless on ThinkPad
CRITERIA
- No Error Message shall appear from AC
- Authentication and NW connection
shall be successfull
EUT QUANTITY
Two systems
EQUIPMENT
PA Networking facilities.
Critical Attribute:[0] : WLS - Wireless

CONFIGURATION
REFERENCE PROCEDURE
STATISTIC INFO
Operating System Win10-32bit Win10-64bit Win7- 64bit Win7- 32bit Total
Test Points
Duration
Workload
# Step actions Win10-32bitWin10-64bitWin7- 64bitWin7- 32bit
1 User Scenario Test AAAA
DETAILS
ATTENTION!! Please follow below information.
1. Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead, then arrange to open defect, if needed.

2. Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case).

3. All Test Activity should be performed with AMT Enabled as Default (applicable on vPro enabled systems).

4. Please check Usability / Cosmetic issues (correct sentence/appropriate display/etc.) and open defect, if needed.

User Scenario Test
Details
Configuration
Check Item / Criteria
Intel
Atheros
User Mode
User Mode
Home - Office Scenario
  1. Apply WEP Profile and connect to ADSL network.
  2. Verify Radio Association , Authentication and Network Connection is successfull
  3. Suspend the system and resume after 10 Minutes.
  4. Apply LEAP Profile of Campus Network.
  5. Verify Radio Association , Authentication and Network Connection is successfull
  6. Apply Multiadapter Profile (Ethernet + LEAP Profile,) with Fastest available Network option . As the Ethernet Cable is not connected, LEAP Wireless profile will be activated.
  7. Suspend the system and Dock the system to Supported Docking Station or Port replicator as applicable.
  8. Connect Ethernet Cable to Ethernet Port in Docking Station /Port Replicator.
  9. Resume from Suspend Mode.
  10. Access Connection shall resume connection to Ethernet profile automatically and IP Address shall be assigned.
Stand alone/ Docked
  • No Error Message shall apprear from Access Connection
  • Authentication and NW connection shall be successfull
  • Wireless switching shall take place automatically without manual intervention
A
A
Business User Switching Scenario
  • Apply VPN (IGN /VTS) profile
    1. Connect to Internet and Check connectivity.
    2. Connect to IBM network and Connect to Notesserver DB.
    3. Switch to WPA-TLS Profile
    4. Connect to Corporate File server and Copy the shared files to local system (300 MB)
    5. After File copying is finishd, Hibernate the system.
    6. Dock the System
    7. Resume from Hibernation
    8. Apply LEAPCKIP Profile
    9. Check Wireless Association / Authentication / Connection is established.
  • Stand alone/ Docked
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successfull
    A
    A
    Meeting Room Scenario
  • Apply LEAP Profile of Campus Network.
  • Check Profile is Associated ,Authenticated and Network Connection is established.
  • Suspend the System by Lid Close.
  • Take the system another room where Campus LEAP Access point is available.
  • Resume the system by opening LID.
  • Check Access Connection resumes connection with the same Wireless Profile , which was used before Suspend Operation.
  • Standalone
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successfull
    A
    A
    User Scenario Test -1
    1. Log in as Administrator and create LAN profile for wired connection using DHCP.
    2. Select disconnect from network when I switch to a different location profile.
    3. Create/apply wireless connection using DHCP and select disable wireless radio when I switch to a different location profile (the location profiles are seperate ones and not autoswitching).
    4. Verify that wired LAN connection is disabled and IP address released when switching to wireless connection.
    5. Verify that wireless connection is disabled and IP address is released when switching back to wired LAN connection.
    6. Create standard user account
    7. Logoff Administrator and login as the standard user
    8. Apply wired LAN profile, verify that IP address is assigned by DHCP server
    9. Select wireless profile and connect, verify that IP address is assigned
    10. run ipconfig /all, wired LAN connection will show IP 0.0.0.0
    11. Apply wired LAN connection without manually disconnecting from wireless connection, verify that IP for wired LAN is assigned
    12. run ipconfig /all,
    13. Confirm that WL connection is not activte and no IP address is assgined to WL adapter
    Standalone
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successfull
    A
    A
    User Scenario Test -2
    - Install Access Coonection and latest WL Driver.
    - Create a multiadapter profile in AC with Ethernet as first priority
    For Wireless settings, select the below settings-
    - Enter the SSID name
    - Select"Enabled-Use 802.1x-EAP CISCO(LEAP)
    - Select "Manual Prompt for LEAP User name and Password"
    - Select "No Network Connection unless User is logged in".
    - Save this profile ---this is the only profile on the system.
    - Restart the system system with the ethernet cable plugged into the
    system.
    - AC connects to the network using the ethernet card.
    - Check that the network works fine.
    - Now, remove the ethernet cable out of the system.
    - Confirm that the WL profile is connected successfully.
    Standalone
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successfull
    A
    A

    OTHER DETAILS
    EUT Quantity : Two systems 1. "Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead."
    2. "Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case)"
    (All Test Activity should be performed with AMT Enabled) Note :
    1. Perform the test in User mode as well as Administrator mode
    2. Please check the version of Access Connection to be used for each product. Access Connection may require specific version of device driver to be installed for the adapters to be tested.
    3. Refer latest Access Connection Function specification for the feature support.

    Perform Access Connection on Japanese OS for SIT for the final verification. Initial stages of testing can be performed on US version. While doing JP coverage, verify the japanese characters, error messages and help menu contents.

    Access Connections applications may have other functions/GUI not mentioned in this test case. Please verify all the available functions and GUI that comes with the particular version of Access Connections. Any updation required to the test case, Please inform Lenovo Engineers.



    Known Limitations/Restrictions/Information
    Known Limitations
    Restriction
    1. Even "Allow all users of this system to create and apply loation profiles" Global settings option check box is checked, limited user account can not modify or create the setting for TCP/IP settings or security settings of local driver share, firewall settings due to Widnows security protection. Such setting is used with Windows default settings. Default is not checked.
    2. Global settings can be only modified by the user when the logon privilege is administrator privilege.
    3. The global settings option "Disable Adhoc connection type option in wireless LAN profiles" is not applicable, if the user create the profile using WIndows wireless LAN property window.
    4. Profile disconnects when user change wireless security type of 802.1x peap to LEAP or vice versa
    (Reference: ECR112851, W7:Profile disconnect when change wireless security type of 802.1x)

    Information
    1. When "Allow all users of this system to create and apply loation profiles" check box is checked, it allows user to create the location profiles and enables location switching regardless of the windows logon privilege (administrator or limited users).
    2. Wireless profiles will be listed in the upper part of the profile list and the Ethernet profiles will be displayed at the lower part of the location profile list on "Automatic switching profile priority window". Due to the faster speed, the Ethernet profiles have higher priority than the wireless profiles.
    3. Static IP address wireless profile will be listed in automtic location switching, as per the new design. However, static IP address ethernet profile will not be listed in automatic location switching.

    Test Item
    Check Item / Criteria
    Configuration
    Result
    Intel
    Atheros
    1. User Scenario Test - No Error Message shall appear from AC
    - Authentication and NW connection
    shall be successfull
    Stand alone
    A
    A

    TEMS Reviewer Log:
    Review Logs
    Keywords:   None
    Requirements :   None
    Attached files :

    Update History:
    This document is not yet modified.