Test Case

Show / Hide direct link   <MAIN> 3489PA: CX4 function verification using Access Connection - PP-80420



Version 1.4
Created on 30/06/2006 12:30:56  by Muralidharan Seshadri
Summary
Preconditions
Status:   New
Priority:   Medium
BASIC INFORMATION
Section:S/W Test Require attachment:No
Team:Network Group:Advanced Function
Lessons Learned:No Phase:SIT, SVT, SIV, (BBFV)
Locations:Inhouse: AWS and Cambridge, Inhouse: AWS, Inhouse: Cambridge, Compal, Flextronics, Quanta, Wistron Owned By:Eiji Ogata/LENOVO
Objective:To verify the CCX-4 functions using AC for all the supported adapters
CRITERIA
All the functions should work as expected with out any side effect/system malfunction
EUT QUANTITY
Two systems
EQUIPMENT
PA Networking facilities
Critical Attribute:[0] : WLS - Wireless

CONFIGURATION
REFERENCE PROCEDURE
STATISTIC INFO
Operating System Win81-64bit Win81-32bit Win7- 64bit Win7- 32bit Total
Test Points
Duration
Workload
# Step actions Win81-64bitWin81-32bitWin7- 64bitWin7- 32bit
1 EAP-FAST with CCX4 PEAPCHAP authentication verification AAAA
2 EAP-FAST with CCX4 PEAPGTC authentication verification AAAA
3 EAP-FAST with CCX4 TLS authentication verification AAAA
4 EAP-FAST CCX4 Enhancement with PEAPCHAP verification AAAA
5 EAP-FAST CCX4 Enhancement with PEAPGTC verification AAAA
6 EAP-FAST CCX4 Enhancement with TLS verification AAAA
7 CCX4 FUNCTION TEST AAAA
8 Network Reliability Test AAAA
DETAILS
ATTENTION!! Please follow below information.
1. Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead, then arrange to open defect, if needed.

2. Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case).

3. All Test Activity should be performed with AMT Enabled as Default (applicable on vPro enabled systems).

4. Please check Usability / Cosmetic issues (correct sentence/appropriate display/etc.) and open defect, if needed.

Note : Perform this test for all the supported wireless adapters

EAP-FAST CCX4 Enhancement with PEAPCHAP verification

Test Item
Criteria
Configuration
Atheros
Intel
EAP-FAST with CCX4 enhancement PEAPCHAP Verification
(Use saved user name and password)

1. Launch Access Connection application version 4.2
2. Create a EAPFAST profile with the following settings:
3. Select "Use IEEE 802.1x EAP (EAP-FAST)" -->click Properties, set data encryption
Data Encryption:WEP
4. Select "Enable EAP-FAST enhancements (CCX4) and make sure the
"Allow authenticated provisioning" option is selected automatically
Select PEAP --->click Configure
5. In the tunneled authentication option ,select authentication protocol,
Authentication protocol:MS-CHAP-V2
6. Click the option `Enter User Credentials`.
7. Enter the Roaming Identity/logon name
8. Choose the option `Use Saved user Name and password`, Enter the credentials and Click `Ok`.
9. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : eapsrv.eap.com) and give OK
10. Save and Apply the profile.
11. Check the Event Log of ACS Server and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
12. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 10-11
13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.3 and confirm steps 10-11
14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.3 and confirm steps 10-11
15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.3 and confirm steps 10-11
  • Authentication should be successful
  • No Error Message related to authentication failure should occur.
  • IP Address should be assigned by DHCP Server
  • Network Connectivity should be available
  • Check the event log in AP and ACS server that authentication is successfull.
Standalone
A
A
EAP-FAST with CCX4 enhancement PEAPCHAP Verification (Prompt temporary name and password)

1. Launch Access Connection application version 4.2
2. Create a EAPFAST profile with the following settings:
3. Select "Use IEEE 802.1x EAP (EAP-FAST)" -->click properties, set data encryption
Data Encryption: WEP
4. Select "Enable EAP-FAST enhancements (CCX4) and make sure the
"Allow authenticated provisioning" option is selected automatically
Select PEAP --->click Configure
5. In the tunneled authentication option, select authentication protocol
Authentication protocol:MS-CHAP-V2
6. Click the option `Enter User Credentials`.
7. Enter the Roaming Identity/logon name
8. Choose the option `Prompt temporary name and password`and Click `Ok`.
9. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : eapsrv.eap.com) and give OK
10. Save and Apply the profile. Enter the correct credentials at the popup window.
11. Check the Event Log of ACS Server/Access Point and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
12. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 10-11
13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.3 and confirm steps 10-11
14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.3 and confirm steps 10-11
15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.3 and confirm steps 10-11
  • Authentication should be successful
  • No Error Message related to authentication failure should occur.
  • IP Address should be assigned by DHCP Server
  • Network Connectivity should be available
  • Check the event log in AP and ACS server that authentication is successfull.
Standalone
A
A
EAP-FAST with CCX4 enhancement PEAPCHAP Verification
(Use Windows logon user name and password)

1. Launch Access Connection application version 4.2
2. Enable SSO Global Settings "Allow wireless connection at WIndows logon (requires system restart)" and restart the system.
3. Create a EAPFAST profile with the following settings:
4. Select "Use IEEE 802.1x EAP (EAP-FAST)" --> click properties, set data encryption
Data Encryption: WEP
5. Select "Enable EAP-FAST enhancements (CCX4) and make sure the
"Allow authenticated provisioning" option is selected automatically
Select PEAP ---> click configure
6. In the tunneled authentication option , select authentication protocol
Authentication protocol:MS-CHAP-V2
7. Click the option `Enter User Credentials`.
8. Enter the Roaming Identity/logon name
9. Choose the option `Use Windows logon user name and password`, and click `Ok`.
10. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : PEAPCHAP) and give OK
11. Save and Apply the profile.
12. Check the Event Log of ACS Server and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
13. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 10-11
14. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.4 and confirm steps 11-12
15. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.4 and confirm steps 11-12
16. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.4 and confirm steps 11-12
  • Authentication should be successful
  • No Error Message related to authentication failure should occur.
  • IP Address should be assigned by DHCP Server
  • Network Connectivity should be available
  • Check the event log in AP and ACS server that authentication is successfull..
Standalone
A
A
EAP-FAST CCX4 PEAPCHAP verification wth Server Certificate Validation
1. Launch Access Connection application version 4.2
2. Create a EAPFAST profile with the following settings:
3. Select "Use IEEE 802.1x EAP (EAP-FAST)" -->click Properties, set data encryption
Data Encryption:WEP
4. Select "Enable EAP-FAST enhancements (CCX4) and make sure the
"Allow authenticated provisioning" option is selected automatically
Select PEAP --->click Configure
5. In the tunneled authentication option ,select authentication protocol,
Authentication protocol:MS-CHAP-V2
6. Click the option `Enter User Credentials`.
7. Enter the Roaming Identity/logon name
8. Choose the option `Use Saved user Name and password`, Enter the credentials and Click `Ok`.
9. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : eapsrv.eap.com)
10.Select the option "Validate Server Certificate" and choose the proper server certificate in the "Certificate issuer" pull down menu.
11. Save and Apply the profile.
12. Check the Event Log of ACS Server and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
13. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 10-11
14. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.3 and confirm steps 11-12
15. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.3 and confirm steps 11-12
16. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.3 and confirm steps 11-12
  • Authentication should be successfull
  • Server certificate should be validated succesfully
  • IP Address should be assigned by DHCP Server
  • Network Connectivity should be available
  • Check the event log in AP and ACS server that authentication is successful
Standalone
A
A

EAP-FAST CCX4 Enhancement with PEAPGTC verification


Test Item
Criteria
Configuration
Atheros
Intel
EAP-FAST with CCX4 Enhancement PEAP-GTC Verification
(Use Saved Username and Password)
  1. Launch Access Connection application version 4.2
  2. Create a EAP-FAST profile with the following settings
  3. Select "Use IEEE 802.1x EAP (EAP-FAST)"-->click properties, set data encryption
Data Encryption: WEP
4. Select "Enable EAP-FAST enhancements (CCX4) and make sure the
"Allow authenticated provisioning" option is selected automatically.
Select PEAP ---> click Configure
5. In the tunneled authentication option select authentication protocol,
Authentication protocol: GTC
6. Click the option `Enter User Credentials`
7. Enter the Roaming Identity/logon name
8. Choose the option `Use Saved user Name and password`, Enter the credentials and Click `Ok`
9. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : PEAP-GTC) and give OK
10. Save and Apply the profile.
11.Check the Event Log of ACS Server and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
12. Change the Data Encryption to "CKIP" in Step.3 and confirm steps 10-11
13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in step.3 and confirm steps 10-11
14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.3 and confirm steps 10-11
15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.3 and confirm steps 10-11
  • Authentication should be successful
  • No Error Message related to authentication failure should occur.
  • IP Address should be assigned by DHCP Server
  • Network Connectivity should be available
  • Check the Access Point and ACS server Event Log and Authentication is successfull.
Standalone
A
A
EAP-FAST with CCX4 Enchancement PEAP-GTC Verification (Prompt temporary name and Password)
  1. Launch Access Connection application version 4.2
  2. Create a EAP FAST profile with the following settings
  3. Select "Use IEEE 802.1x EAP(EAP-FAST)"-->click properties, set data encryption Data Encryption : WEP
  4. Select "Enable EAP-FAST enhancements (CCX4) and make sure the
"Allow authenticated provisioning" option is selected automatically
Select PEAP ---> click Configure
5. In the Tunneled Authentication option select authentication protocol
Authentication protocol : GTC
6. Click the option `Enter User Credentials`
7. Enter the Roaming Identity/logon name
8. Choose the option `Prompt temporary name and password`, Enter the credentials and Click `Ok`
9. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : PEAP-GTC) and give OK
10. Save and Apply the profile. Provide the username and password when prompted
11. Check the Event Log of ACS Server and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
12. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 10-11
13. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.3 and confirm steps 10-11
14. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.3 and confirm steps 10-11
15. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.3 and confirm steps 10-11
  • Authentication should be successful
  • No Error Message related to authentication failure should occur.
  • IP Address should be assigned by DHCP Server
  • Network Connectivity should be available
  • Check the Access Point and ACS server Event Log and Authentication is successfull.
Standalone
A
A
EAP-FAST with CCX4 Enhancement PEAP-GTC Verification (Using Hardware Token)
  1. Launch Access Connection application version 4.2
  2. Create a PEAP-GTC profile with the following settings
  3. Select "Use IEEE 802.1x EAP(EAP-FAST)"-->click properties, set data encryption Data Encryption : WEP
  4. Select "Enable EAP-FAST enhancements (CCX4) and make sure the
"Allow authenticated provisioning" option is selected automatically
Select PEAP ---> click Configure
5. In the Tunneled Authentication option select authentication protocol
Authentication protocol : GTC
6. Click the option "Enter user credentials"
7. Enter the roaming Identity/logon name
8. Choose the option `Use one time token (password)`, Enter the credentials and Click `Ok``
9. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : PEAP-GTC) and give OK
10. Save and Apply the profile.
11. "Enter Your Token Number" option will appear
12. Enter here the first 4 digit PIN assigned on specific HW Token + the 6 digit PIN appearing on the HW token screen.Example for HW Token assigned PIN (pahwtoken:7297 + the 6 digit # you will see in the hw token screen)
13. Change the Data Encryption to "CKIP" in Step.3 and confirm steps 10-11
14. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.3 and confirm steps 10-11

15. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.3 and confirm steps 10-11
16. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.3 and confirm steps 10-11.
  • Authentication should be successful
  • No Error Message related to authentication failure should occur.
  • IP Address should be assigned by DHCP Server
  • Network Connectivity should be available
  • Check the Access Point and ACS server Event Log and Authentication is successfull.
Standalone
A
A
EAP-FAST with CCX4 Enahancement PEAP-GTC Verification (Using Software Token)
  1. Launch Access Connection application version 4.2
  2. Create a PEAP-GTC profile with the following settings
  3. Select "Use IEEE 802.1x EAP(EAP-FAST)"-->click properties, set data encryption Data Encryption : WEP
  4. Select "Enable EAP-FAST enhancements (CCX4) and make sure the
"Allow authenticated provisioning" option is selected automatically
Select PEAP ---> click Configure
5. In the Tunneled Authentication option select authentication protocol
Authentication protocol : GTC
6. Click the option "Enter user credentials"
7. Enter the roaming Identity/logon name
8. Choose the option `Use one time token (password)`, Enter the credentials and Click `Ok``
9. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : PEAP-GTC) and give OK
10. Save and Apply the profile.
11. "Enter Your Token Number" option will appear
12. Enter the Password: (8 digit PIN appearing on the SW token screen)
13. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 10-11
14. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.3 and confirm steps 10-11
15. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.3 and confirm steps 10-11
16. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.3 and confirm steps 10-11.
  • Authentication should be successful
  • No Error Message related to authentication failure should occur.
  • IP Address should be assigned by DHCP Server
  • Network Connectivity should be available
  • Check the Access Point and ACS server Event Log and Authentication is successfull.
Standalone
A
A
EAP-FAST CCX4 PEAP-GTC Verification wth Server Certificate Validation
1. Launch Access Connection application version 4.2
2. Create a EAPFAST profile with the following settings:
3. Select "Use IEEE 802.1x EAP (EAP-FAST)" -->click Properties, set data encryption
Data Encryption:WEP
4. Select "Enable EAP-FAST enhancements (CCX4) and make sure the
"Allow authenticated provisioning" option is selected automatically
Select PEAP --->click Configure
5. In the tunneled authentication option ,select authentication protocol,
Authentication protocol:GTC
6. Click the option `Enter User Credentials`.
7. Enter the Roaming Identity/logon name
8. Choose the option `Use Saved user Name and password`, Enter the credentials and Click `Ok`.
9. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : eapsrv.eap.com)
10.Select the option "Validate Server Certificate" and choose the proper server certificate in the "Certificate issuer" pull down menu.
11. Save and Apply the profile.
12. Check the Event Log of ACS Server and Authentication is successfull. Verify the EAP Type is shown as PEAP and Correct MAC Address of the Wireless Client system is shown in the Eventlog
13. Change the Data Encryption to "CKIP" in Step.4 and confirm steps 10-11
14. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in Step.3 and confirm steps 11-12
15. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.3 and confirm steps 11-12
16. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.3 and confirm steps 11-12
  • Authentication should be successfull
  • Server certificate should be validated succesfully
  • IP Address should be assigned by DHCP Server
  • Network Connectivity should be available
  • Check the event log in AP and ACS server that authentication is successful
Standalone
A
A

EAP-FAST CCX4 Enhancement with TLS verification

Test Item Check Item / Criteria
Configuration
Result
Intel
Atheros
Wireless Client Configuration
  1. Connect the test System to Wndows 2003 / Windows 2000 Domain Network by ethernet
  2. Register the Wireless Client as Domain Member of Windows 2003 /Windows 2000 Domain
  3. Add the Domain User to the Local Administrator group.
  4. Log in as the Domain user.
  5. Download Simple User Certificate using Internet Explorer or Microsoft Management Console from Certification Server in Windows 2003/ Windows 2000 Domain. (For ex: 192.168.21.1 /certsrv)
  6. After Certificate is successfully downloaded, from Internet Explorer, Click Tools>Internet options>content>certification and verify the downloaded certificate is listed. Click Advanced tab and select `Client Authentication` Box in Certificate purposes option.

  • The User Certificate shall be successfully downloaded
  • No Error Message while downloading the Certificate


Standalone


A


A
EAP-FAST CCX4 Enhancement TLS verification with client certificate validation

  1. Launch Access Connection application version 4.2
  2. Create a EAP-FAST profile with the following settings
  3. Select "Use IEEE 802.1x EAP (EAP-FAST)"-->click properties, set data encryption
Data Encryption: WEP
4. Select "Enable EAP-FAST enhancements (CCX4) and make sure the
"Allow authenticated provisioning" option is selected automatically.
Select TLS---> click Configure

5. Check the option " use client certificate" and select the proper user certificate and click OK
6. Save and Apply the profile.
7.Check the ACS Event Log and make sure authentication is successfull.
8. Change the Data Encryption to "CKIP" in Step.3 and confirm steps 6-7
9. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in step.3 and confirm steps 6-7
10. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.3 and confirm steps 6-7
11. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.3 and confirm steps 6-7
  • Authentication should be successful
  • No Error Message related to authentication failure should occur.
  • IP Address should be assigned by DHCP Server
  • Network Connectivity should be available
  • Check the Access Point and server Event Log and Authentication is successfull.
Standalone
A
A
EAP-FAST CCX4 Enhancement TLS verification with server certificate validation
  1. Launch Access Connection application version 4.2
  2. Create a EAP-FAST profile with the following settings
  3. Select "Use IEEE 802.1x EAP (EAP-FAST)"-->click properties, set data encryption
Data Encryption: WEP
4. Select "Enable EAP-FAST enhancements (CCX4) and make sure the
"Allow authenticated provisioning" option is selected automatically.
Select TLS---> click Configure

5. Check the option " validate server certificate" and select the proper server certificate and click OK .
6. Choose the option Server Name Must match Exactly or Domain Name must end in specified name and type the Server Name (For example : TLS.com) and give OK
6. Save and Apply the profile.
7.Check the ACS Event Log and make sure authentication is successfull.
8. Change the Data Encryption to "CKIP" in Step.3 and confirm steps 6-7
9. Change the AP Authenticaion to "WPA" and Data Encryption to "TKIP" in step.3 and confirm steps 6-7
10. Change the AP Authenticaion to "WPA" and Data Encryption to "AES" in Step.3 and confirm steps 6-7
11. Change the AP Authenticaion to "WPA2" and Data Encryption to "AES" in Step.3 and confirm steps 6-7
  • Authentication should be successful
  • No Error Message related to authentication failure should occur.
  • IP Address should be assigned by DHCP Server
  • Network Connectivity should be available
  • Check the Access Point and server Event Log and Authentication is successfull.
Standalone
A
A

CCX4 FUNCTION TEST

CCX4 Function TEST
XP
Win 7
Vista
EAP FAST-PEAP MSCHAP
Use Windows Username and Password Check PAC is provisioned
Check profofile can connect at prelogon
Check PAC is slected in AC Profile
Check multiple windows user can use the same profile
Saved user name password Check PAC is provisioned
Check can connect at prelogon
Check PAC is selected in AC Profile
Check multiple windows user can use the same profile
Prompt user name and password Check PAC is provisioned
Check can connect at prelogon
Check PAC is selected in AC Profile
Check multiple windows user can use the same profile
EAPFAST-TLS user certificate
Check PAC is provisioned
Check PAC is selected in AC Profile
Check multiple windows user can use the same profile
EAPFAST-TLS Computer certificate
Check PAC Can be provisioned
Check PAC is selected in AC Profile
Check profile can connet at prelogon
Check multiple windows user can use the same profile
EAP FAST-PEAP GTC
Saved user name password Check PAC is provisioned
Check profile can connect at prelogon
Check PAC is selected in AC Profile
Check multiple windows user can use the same profile
One time token Check PAC is provisioned
Check can connect at prelogon
Check PAC is selected in AC Profile
Check multiple windows user can use the same profile
Note: For connecting at prelogon AC gina should be enabled

Network Reliability Test

Test Item
Check Item / Criteria
Configuration
Result
Intel
Atheros
Warm Boot Tests
  1. After Successfull authentication and Network Connection is established, Restart the System
  2. Enable the error log by going to Diagnostic Tools of Access Connection and under Event log Enable the logging.
  3. Check Wireless Connection is restored to the same EAPFAST Profile used before restarting the system
  4. Repeat the steps 1-2 for 10 Times and verify the criteria. Please make sure you clear the Error Log after successfull completion of each Restart operation
  5. If any error Message is found during Reboot operation, Send the Access Connection Error Log, which is saved under the folder :-C:\Program Files\ThinkPad\ConnectUtilities\errorlog to PA Yamato team for Investigation
  • Authentication shall be successfull after each Restart
  • Network Connectivity shall be established after each Restart
  • Network connection be restored to Previously used Profile unless AP is powered off
  • No Error Message after Restart

Access Connection Profile (WinXP and Win2K)


A


A
Connect /Disconnect Tests
  1. Launch Access Connection. Connect the Wireless Profile > EAPFAST. Verify Authentication is successfull and Network Connection is established.
  2. Disconnect the Profile. Connect the same profile again.Verify Authentication is successfull and Network Connection is established.
  3. Repeat this operation in Step 1-2 for five times.


  • Authentication and Network Connection shall be successfull after every Disconnect / Connect operation
  • No Error Message occurs


Access Connection Profile (WinXP and Win2K)


A


A
Cold Boot Tests
  1. After Successfull authentication and Network Connection is established, Shutdown the System
  2. Power On the system again
  3. Login to Windows Check Wireless Connection is restored to the same EAPFAST Profile used before restarting the system
  4. Repeat the steps 1-3 for 10 Times and verify the criteria

  • Authentication and NW Connectivity shall be successfull after Cold Boot
  • No Error Message occurs


Access Connection Profile


A


A
Power Management Tests - UR-2727
Suspend
  1. After Successful authentication and Network Connection is established, Press Fn+F4 to suspend the system.
  2. Resume the system by presing the Fn key after 1 minute.
  3. Ensure Authentication is successfull and Network Connectivity is restored to the previously connected AP /Network.
  4. Repeat Steps 1-3 for 10 times and verify the criteria

Hibernate
  1. After Successful authentication and Network Connection is established, Press Fn+F12 to hibernate the system.
  2. Resume the system by pressing the Fn key after 1 minute.
  3. Ensure Authentication is successfull and Network Connectivity is restored to the previously connected AP /Network.
  4. Repeat Steps 1-3 for 10 times and verify the criteria

Lid-close
  1. After Successfull authentication and Network Connection is established close the lid to suspend the system
  2. Resume the system by opening the lid after 1 minute.
  3. Ensure Authentication is successfull and Network Connectivity is restored to the previously connected AP /Network.
  4. Repeat Steps 1-3 for 10 times and verify the criteria
  • Authentication shall be successfull after each PM
  • Network Connectivity shall be established after each PM
  • No Error Message occurs
  • For Intel Wireless Cards in Windows 7 and Vista, Wireless profile authentication does not prompt even if "remember my user credentials" option is unchecked. This is working as designed using Intel Wireless LAN cards. (Ref:ECR83575, ECR86357) (UR-03039AP)
OTHER DETAILS
EUT Quantity : Two systems 1. "Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead."
2. "Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case)"
(All Test Activity should be performed with AMT Enabled) Note :
1. Perform the test in User mode as well as Administrator mode
2. Please check the version of Access Connection to be used for each product. Access Connection may require specific version of device driver to be installed for the adapters to be tested.
3. Refer latest Access Connection Function specification for the feature support.

Perform Access Connection on Japanese OS for SIT for the final verification. Initial stages of testing can be performed on US version. While doing JP coverage, verify the japanese characters, error messages and help menu contents.

Access Connections applications may have other functions/GUI not mentioned in this test case. Please verify all the available functions and GUI that comes with the particular version of Access Connections. Any updation required to the test case, Please inform Lenovo Engineers.



Known Limitations/Restrictions/Information
Known Limitations
1. For Intel Wireless Cards in Windows 7 and Vista, Wireless profile authentication does not prompt even if "remember my user credentials" option is unchecked. This is working as designed using Intel Wireless LAN cards. (Ref:ECR83575, ECR86357)
Restriction
1. Even "Allow all users of this system to create and apply loation profiles" Global settings option check box is checked, limited user account can not modify or create the setting for TCP/IP settings or security settings of local driver share, firewall settings due to Widnows security protection. Such setting is used with Windows default settings. Default is not checked.
2. Global settings can be only modified by the user when the logon privilege is administrator privilege.
3. The global settings option "Disable Adhoc connection type option in wireless LAN profiles" is not applicable, if the user create the profile using WIndows wireless LAN property window.
4. Profile disconnects when user change wireless security type of 802.1x peap to LEAP or vice versa
(Reference: ECR112851, W7:Profile disconnect when change wireless security type of 802.1x)

Information
1. When "Allow all users of this system to create and apply loation profiles" check box is checked, it allows user to create the location profiles and enables location switching regardless of the windows logon privilege (administrator or limited users).
2. Wireless profiles will be listed in the upper part of the profile list and the Ethernet profiles will be displayed at the lower part of the location profile list on "Automatic switching profile priority window". Due to the faster speed, the Ethernet profiles have higher priority than the wireless profiles.
3. Static IP address wireless profile will be listed in automtic location switching, as per the new design. However, static IP address ethernet profile will not be listed in automatic location switching.



Test
WinXP
Win 7
Atheros
Intel
Atheros
Intel
EAP-FAST CCX4 Enhancement with PEAPCHAP verification
A
A
A
A
EAP-FAST CCX4 Enhancement with PEAPGTC verification
A
A
A
A
EAP-FAST CCX4 Enhancement with TLS verification
A
A
A
A



EAP-FAST with CCX4 PEAPCHAP authentication verification
Authentication
Authentication
Server
User Credential
Encryption
Atheros
Intel
EAP-FAST PEAPCHAP
CISCO ACS 4.0
Windows Username & Password
WEP
A
A
(CCX4)
Saved Username & Password
WEP
A
A
Prompt temporary Username & Password
WEP
A
A
Machine certificate Validation
WEP
A
A
Server certificate validation
WEP
A
A
CISCO ACS 4.0
Windows Username & Password
CKIP
A
A
Saved Username & Password
CKIP
A
A
Prompt temporary Username & Password
CKIP
A
A
Machine certificate Validation
CKIP
A
A
Server certificate validation
CKIP
A
A
CISCO ACS 4.0
Windows Username & Password
TKIP
A
A
Saved Username & Password
TKIP
A
A
Prompt temporary Username & Password
TKIP
A
A
Machine certificate Validation
TKIP
A
A
Server certificate validation
TKIP
A
A
CISCO ACS 4.0
Windows Username & Password
AES
A
A
Saved Username & Password
AES
A
A
Prompt temporary Username & Password
AES
A
A
Machine certificate Validation
AES
A
A
Server certificate validation
AES
A
A


EAP-FAST with CCX4 PEAPGTC authentication verification
Authentication
Authentication
Server
User Credential
Encryption
Atheros
Intel
EAP-FAST PEAPGTC
ACS 4.0/RSA Saved Username & Password
WEP
A
A
(CCX4)
AutoPrompt Username & Password
WEP
A
A
Prompt temporaryUsername & Password
WEP
A
A
Machine certificate Validation
WEP
A
A
Server certificate validation
WEP
A
A
Hardware token
WEP
A
A
ACS 4.0/RSA Saved Username & Password
CKIP
A
A
AutoPrompt Username & Password
CKIP
A
A
Prompt temporary Username & Password
CKIP
A
A
Machine certificate Validation
CKIP
A
A
Server certificate validation
CKIP
A
A
Hardware token
CKIP
A
A
ACS 4.0/RSA Saved Username & Password
TKIP
A
A
AutoPrompt Username & Password
TKIP
A
A
Prompt temporaryUsername & Password
TKIP
A
A
Machine certificate
TKIP
A
A
Server certificate
TKIP
A
A
Hardware token
TKIP
A
A
ACS 4.0/RSA Saved Username & Password
AES
A
A
Prompt temporary Username & Password
AES
A
A
Machine certificate
AES
A
A
Server certificate
AES
A
A
Hardware token
AES
A
A


EAP-FAST with CCX4 TLS authentication verification.
Authentication
Authentication
Server
User Credential
Encryption
Atheros
Intel
EAP-FAST TLS
Cisco ACS4.0
Certificate
WEP
A
A
(CCX4)
Cisco ACS4.0
Certificate
CKIP
A
A
Cisco ACS4.0
Certificate
TKIP
A
A
Cisco ACS4.0
Certificate
AES
A
A

TEMS Reviewer Log:
Review Logs
Keywords:   None
Requirements :   None
Attached files :

Update History:
This document is not yet modified.