Test Case

Show / Hide direct link   <ROOT> 3571PA: NW adapters Reliability & Integration function test - PP-80374



Version 1.2
Created on 20/10/2006 16:19:21  by Muralidharan Seshadri
Summary
Preconditions
Status:   New
Priority:   Medium
BASIC INFORMATION
Section:S/W Test Require attachment:No
Team:Network Group:Advanced Function
Lessons Learned:No Phase:SIV (BBFV), SIT
Locations:Inhouse: AWS and Cambridge, Inhouse: AWS, Inhouse: Cambridge, Compal, Flextronics, Quanta, Wistron Owned By:Eiji Ogata/LENOVO
Objective:To verify the system integrity with all the supported adapters/applications duly configured in the system. This test assume the full configured or specially purposed customer environment.
CRITERIA
All devices, applications must work togther without any performance degradation/system malfunction
EUT QUANTITY
Two systems
EQUIPMENT
PA Networking facilities.
Critical Attribute:[0] : WLS - Wireless

CONFIGURATION
REFERENCE PROCEDURE
STATISTIC INFO
Operating System Win81-64bit Win81-32bit Win10-32bit Win10-64bit Win7- 64bit Win7- 32bit Total
Test Points
Duration
Workload
# Step actions Win81-64bitWin81-32bitWin10-32bitWin10-64bitWin7- 64bitWin7- 32bit
1 Driver Installation/Uninstallation AAAAAA
2 Network/Wireless with Harddrive Active Protection AAAAAA
3 FnF5 Verification with Global Switch/BIOS setting AAAAAA
4 F9 Verification with Software Switch/BIOS setting AAAAAA
5 Wireless Roaming AAAAAA
6 Integration with VPN AAAAAA
7 Integration with all devices AAAAAA
8 User Scenario Test AAAAAA
DETAILS
ATTENTION!! Please follow below information.
1. Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead, then arrange to open defect, if needed.

2. Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case).

3. All Test Activity should be performed with AMT Enabled as Default (applicable on vPro enabled systems).

4. Please check Usability / Cosmetic issues (correct sentence/appropriate display/etc.) and open defect, if needed.

SUPPORTED ADAPTER FOR THIS PRODUCT
Adapter Name
Card Revision (Example 3B2....)
Firmware Version
Phase Entry :
Phase Exit :
Phase Entry :
Phase Exit :



Fill out the following or attach the ATS system information file. Specify driver/EEPROM/firmware/card revision tested for Entry/Exit period.
Win-8 32

Phase Entry :
Phase Exit :
Win-7

Phase Entry :
Phase Exit :
EUT
BIOS
H8
Preload Image
Wireless Driver
Ethernet Driver details
EEPROM for Ethernet
Modem Driver
Audio
Video
ThinkPad Utility
Access Connections
Other driver details
Wireless Access Point details and Firmware Information


Scenario Focus Remarks
1. Wireless Roaming - Verify basic AccessConnection function
- Use different Access Point (802.11b, 802.11a/b, 802.11a/g)
- Move around in the office
Add PM verification
2. Profile change (Desktop -> Mobile) - Verify basic AccessConnection function
- Docked -> undocked configuration
Add PM verification
3. Office -> Home environment - Wired network (office) -> ADSL (home)
- Wireless network (office (outside)) -> Dialup (home) etc.
Add PM verification
4. Network performance monitor - Run monitor tool while test Check everyday
5. Bluetooth, Mobile phone (PHS Data card) - Network environment co-existance
6. Web Streaming (Longrun) - Web TV etc




1. Configur all supported WLAN/WWAN/WiMax/Ethernet/Modem drivers.
2. This test should be performed for all the adapters supported by the product. For the adapter support, refer the test plan

Driver Installation/Uninstallation
Win-8
Win-7
Install Wireless driver as per the build letter
Create Profile using Access Connection and confirm that the profile can be created and WL connection is working fine.
Uninstall Wireless driver as per the build letter
Reinstall Wireless driver and confirm that the profile created earlier is working fine.
Perform overwrite installtion of Wireless driver and confirm that the wireless connection is working fine.
Perform the above steps for all the supported wireless adapters.
Perform Inf and Setup Installation if both are supported

Please note that in some cases, uninstallation/reinstallation of Access Connection may be necessary/
Install Ethernet driver as per the build letter
Create Profile using Access Connection and confirm that the profile can be created and WL connection is working fine.
Uninstall ethernet driver as per the build letter
Reinstall ethernet driver and confirm that the profile created earlier is working fine.
Perform overwrite installtion of ethernet driver and confirm that the ethernet connection is working fine.
Install Bluetooth driver as per the build letter.
Confirm that the Bluetooth is working fine.
Uninstall Bluetooth driver as per the build letter
Reinstall Bluetooth driver and confirm that the profile created earlier is working fine.
Perform overwrite installtion of Bluetooth driver and confirm that the Bluetooth connection is working fine.
For Windows XP, verification needs to be done by using MS Bluetooth stack driver and Widcomm driver.

For Windows 2000, Use Widcomm driver.
Stand alone
With the configuration of Wireless, Ethernet and Bluetooth
- Perform Power management functions (Suspend, Hibernation) - minimum of 5 times.
- Confirm that the system can connect to network after PM
- Use Fn+F5 key to switch off / ON WL/Bluetooth Radio and confirm the radio status
- Confirm that the system can connect to network after Power OFF/ON.
Perform the above steps minimum of 5 times.
Radio status before and after PM should be same
Radio status before and after system restart should be same


Network/Wireless with Harddrive Active Protection (Supported for latest products only... Pls confirm the product support)

Test Item
RESULT
Win-8
Win-7
Install Harddisk active protection driver
From task tray, click the hard disk icon to invoke IBM Haddrive Protection system properties tab
- Click Enable hard active protection system option
- Click 'Temporarily disable hard drive active protection system while a repetitive vibration (such as that experienced when in a train or automobile) is detected
- Select Show harddrive active protection icon on the system tray and
Play sound when hard drive is spinning up or down.

1. Connect to Office network via Wireless using Access connection profile
2. Shake the system manually well to confirm that the Hard disk spinning process
3. Confirm that the wireless still works fine.
4. Map shared network directory and transfer files of more than 300MB file size (single file size)
5. Confirm that the network is working fine and system is stable in that condition.

Perform step 1-5 for all the wireless adapter and ethernet adapter also.
A
A


FnF5 Verification with Global Switch/BIOS setting [UR-2711AP]
Configure system with the supported Wireless LAN/WAN adapters. WAN radio also must be confirmed
Device
BIOS Settings
Global Switch
Criteria
Result
Result
Win-8
Win 7
Wireless
Enabled with Radio On
ON
FnF5 should list Wireless with Turn ON/OFF options
Should be able to Turn ON/OFF Wireless Radio
A
A
Enabled with Radio Off
ON
FnF5 should list WL but should not allow to change WL Radio ON/OFF
A
A
Disabled with Radio On or Off
ON
FnF5 should not show Wireless
A
A
Enabled with Radio On
OFF
FnF5 message saying " To use wireless radios:Please turn on the hardware wireless radio switch as shown. Show the location of hardware wireless radio switch" should appear
A
A
Enabled with Radio Off
OFF
FnF5 message saying " To use wireless radios:Please turn on the hardware wireless radio switch as shown. Show the location of hardware wireless radio switch" should appear
A
A
Disabled with Radio On or Off
OFF
FnF5 message saying " To use wireless radios:Please turn on the hardware wireless radio switch as shown. Show the location of hardware wireless radio switch" should appear
A
A



F9 Verification with Software Switch/BIOS setting

Configure system with the supported Wireless LAN/WAN adapters. WAN radio also must be confirmed
Device
BIOS Settings
Software Switch
Criteria
Result
Result
Win-8
Win 7
Wireless
Enabled with Radio On
ON
FnF5 / F9 should list Wireless with Turn ON/OFF options
Should be able to Turn ON/OFF Wireless Radio
A
A
Enabled with Radio Off
ON
FnF5 / F9 should list Wireless with Turn ON/OFF options
Should allow to change WL Radio ON/OFF
A
A
Disabled with Radio On or Off
ON
FnF5 / F9 should show Wireless
A
A
Enabled with Radio On
OFF
FnF5 / F9 message saying "All radios are Off. To use wireless radios. Please turn on master control above." should appear
A
A
Enabled with Radio Off
OFF
FnF5 / F9 message saying "All radios are Off. To use wireless radios. Please turn on master control above." should appear
A
A
Disabled with Radio On or Off
OFF
FnF5 / F9 message saying "All radios are Off. To use wireless radios. Please turn on master control above." should appear
A
A



1. Perform entire UST test for all the supported Wireless adapters
Day1 Day time - Driver Installation/Uninstallation
Install Wireless driver as per the build letter
Create Profile using Access Connection and confirm that the profile can be created and WL connection is working fine.
Uninstall Wireless driver as per the build letter
Reinstall Wireless driver and confirm that the profile created earlier is working fine.
Perform overwrite installtion of Wireless driver and confirm that the wireless connection is working fine.
Perform the above steps for all the supported wireless adapters.
Perform Inf and Setup Installation if both are supported

Please note that in some cases, uninstallation/reinstallation of Access Connection may be necessary/
Install Ethernet driver as per the build letter
Create Profile using Access Connection and confirm that the profile can be created and WL connection is working fine.
Uninstall ethernet driver as per the build letter
Reinstall ethernet driver and confirm that the profile created earlier is working fine.
Perform overwrite installtion of ethernet driver and confirm that the ethernet connection is working fine.
With the configuration of Wireless, Ethernet and Bluetooth
With the configuration of Wireless, Ethernet and Bluetooth
- Establish the connectivity through all the supported adapters
- While establishing the connectivity with BT, download files through WLAN.
- Ensure that the WLAN and system performance is not affected and all the functions work correctly.

- Perform Power management functions (Suspend, Hibernation) - minimum of 5 times.
- Confirm that the system can connect to network after PM
- Use Fn+F5 key to switch off / ON WL/WWAN Radio and confirm the radio status
- Confirm that the system can connect to network after Power OFF/ON.
Perform the above steps minimum of 5 times.
Radio status before and after PM should be same
Radio status before and after system restart should be same
With the configuration of Wireless, Ethernet and Bluetooth / WiGig
- Establish the connectivity through all the supported adapters
- While establishing the connectivity with BT, download files through WLAN. Stream video through WiGig dock.
- Ensure that the WLAN and system performance is not affected and all the functions work correctly.
- Perform Power management functions (Suspend, Hibernation) - minimum of 5 times.
- Confirm that the system can connect to network after PM
- Use hotkey [FnF5 / F8 / F9 based on product support] key to switch off / ON WL/WWAN Radio and confirm the radio status
- Confirm that the system can connect to network after Power OFF/ON.
Perform the above steps minimum of 5 times.
Radio status before and after PM should be same
Radio status before and after system restart should be same
Day-1 : Night time

Day2 - Day time (Wireless Roaming)
  • Recover the latest preload image
  • Install the latest drivers
  • Configure applications.
Configure multiple wireless profile in AccessConnectionWLS1 : WPA
WLS2 : LEAP
WLS3 : 802.1x
WLS4 : 128bit WEP key
WLS5 : No WEP
  • Perform the test as mentioned in the below table
  • Create Profiles using Ethernet, Modem
    1. In the Device Manager->Network adapter->Power Management->select the following options.
    2. "Allow this device to bring the computer out of standby" and also Ensure that the Wake on Setting is set to wake the system for 'Wake on Link'
    3. Create multiple profiles using Wireless adapters with the following options
    4. No WEP, WEP key, LEAP, WPA, 802.1x connecting to different Access Points
    5. In the Location switching menu-> select 'Switch ethernet and wireless profiles automatically"
    6. Set the priority of the Wireless profiles in the following order
    7. WEP key->No WEP key
    8. In the above step, if mulitiple AP's are available, select the profile accordingly
    9. Connect to Ethernet profile
    10. Suspend the system
    11. Remove the Ethernet cable and resume the system from Suspend
    12. Confirm that the Wireless profile mentioned in the location switching is connected
    13. Switch off the AP (or go away from that AP) to connect to the profile that has different AP/WEP settings
    14. Confirm that the profile is connected properly and network is working fine.
    • All profiles should connect to network properly
    • Automatic roaming should take place as mentioned in the roaming list
    • No system malfunction or abnormal behaviour.
    • All the GUI should have correct information and icons.
    Stand alone
  • Now suspend the system again
    1. Dock the system to Docking station
    2. Insert ethernet adapte(PC Card)r in the docking station slot and cable connected to network
    3. Create a profile for the adapter available in the docking station.
    4. Use the global settings option ' Undock the system when a location profile is used that does not use a docking station network adpater"
    5. Apply this profile and confirm that the profile is connected and working properly.
    6. Switch the profile to the wireless profile manually
    7. Confirm that the system is undocked automatically when this switching occurs.
    8. Now take the system away from the docking station and confirm that the profile is connected properly and network is working fine
    9. Suspend the system and leave the system for 2 minutes
    10. Insert the ethernet cable and confirm that the system wakes up from suspend
    • All profiles should connect to network properly
    • Automatic roaming should take place as mentioned in the roaming list
    • No system malfunction or abnormal behaviour.
    • All the GUI should have correct information and icons.
    Stand alone
  • Now confirm that the profile switches automatically from wireless to ethernet
    1. Remove the ethernet cable again.
    2. Now profile will be switched back to wireless
    3. Dock the system.
    4. Confirm that the system switches back to ethernet of the docking station adapter.
    5. Verify that all the functions are working fine.
    6. Verify for the GUI and correctness of the information.
    • All profiles should connect to network properly
    • Automatic roaming should take place as mentioned in the roaming list
    • No system malfunction or abnormal behaviour.
    • All the GUI should have correct information and icons.
    Stand alone
    Day-2 (Night time)- Configure Internet
    - Apply Wireless profile and connect to internet
    - Play continuous movie from the trusted website (microsoft.com, ibm.com etc..)
    - confirm that the movie/audio can be played continuously and no system impact
    • No wireless related issues like radio off/on automatically
    • No system performance degradation or system malfunction

    Modem to test to be performed only if the Modem adapter is supported.
    Day-3 - Day time (VTS-NB Narrow band profile)
    • Create following profile in AccessConnection
      LAN : Wireless LAN
      Modem(dial-up) - set automatic connect when this profile is selected
      • Connect Wireless LAN and access to office network
      • Change the profile to Modem
      • Make sure autodial functions properly
      • Suspend the system then wake up, check Modem is disconnected
      • Resume the system then change the profile to LAN
      • Move to the no wireless signal area, then comeback after few minutes.
      • Confirm that the wireless is connected correctly.
  • Create Modem profile in AccessConnection
    • Dial-up one access point of Modem service provider
    • Make sure the connection
    • While connected change the AccessConnecion profile to Wireless
    • Make sure Wireless connection is ready and modem connectivity was logged out
    • While connected Wireless, change the AccessConnection profile to Modem.
    • Make sure Dial-up will be performed automatically, then connection is successful
  • Day-3 - Night time
    Application Stress Test

    Drive (Network) sharing

    - Share the VCD/MPEG samples in a network drive (another system)
    - Play the Video CD/MPEG1,2 files from the shared network drive

    MS Office (Latest version) - Network installation

    - Install MS Office latest version from shared network drive or from server
    - Open the Office latest version application (Word / Excel).
    - Save the file directly to the server location
    - Insert the 1GB Micro drive
    - Copy contents from network drive to the flash card

    Lotus Notes- Database Replication
    - Install Lotus Notes domino
    - Play Video files fom the DVD drive
    - Connect to Mail sever and office network
    - Replicate notes database to your local system while Video is playing
    Stand alone

    Day-4- Day time - Integration with all devices
    - Connect to Office network via Wireless using Access connection profile
    - Map shared network directory and transfer files.
    - While transferring files, send a fax using modem
    - Power ON WWAN device
    - Simultanously search WWAN tower and connect
    - Download files using WWAN
    File copy - Stress test

    - Connect to Office network via Wireless using Access connection profile
    - Open mutliple applications like MS Office suite (Word,Excel,Powerpoint etc..)
    - Map shared network directory and transfer files of more than 1GB file size(ghost image)
    - Confirm that the network is working fine and system is stable in that condition
    Install Harddisk active protection driver
    From task tray, click the hard disk icon to invoke IBM Haddrive Protection system properties tab
    - Click Enable hard active protection system option
    - Click 'Temporarily disable hard drive active protection system while a repetitive vibration (such as that experienced when in a train or automobile) is detected
    - Select Show harddrive active protection icon on the system tray and
    Play sound when hard drive is spinning up or down.

    1. Connect to Office network via Wireless using Access connection profile
    2. Shake the system manually well to confirm that the Hard disk spinning process
    3. Confirm that the wireless still works fine.
    4. Map shared network directory and transfer files of more than 300MB file size (single file size)
    5. Confirm that the network is working fine and system is stable in that condition.

    Perform step 1-5 for all the wireless adapter and ethernet adapter also.
    Stand alone
    Day-4 : Night time


    User Scenario Test

    Details
    Configuration
    Check Item / Criteria
    User Mode
    User Mode
    Home - Office Scenario
    1. Apply WEP Profile and connect to ADSL network.
    2. Verify Radio Association , Authentication and Network Connection is successfull
    3. Suspend the system and resume after 10 Minutes.
    4. Apply Profile of office Network.
    5. Verify Radio Association , Authentication and Network Connection is successfull
    6. Apply Multiadapter Profile (Ethernet + office netowork Profile,) with Fastest available Network option . As the Ethernet Cable is not connected, office netowrk Wireless profile will be activated.
    7. Suspend the system and Dock the system to Supported Docking Station or Port replicator as applicable.
    8. Connect Ethernet Cable to Ethernet Port in Docking Station /Port Replicator.
    9. Resume from Suspend Mode.
    10. Access Connection shall resume connection to Ethernet profile automatically and IP Address shall be assigned.
    Stand alone/ Docked
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successfull
    • Wireless switching shall take place automatically without manual intervention
    Business User Switching Scenario
  • Apply VPN profile
    1. Connect to Internet and Check connectivity.
    2. Connect to office network using VPN and connect to office servers
    3. Switch to WPA-TLS Profile
    4. Connect to Corporate File server and Copy the shared files to local system (300 MB)
    5. After File copying is finishd, Hibernate the system.
    6. Dock the System
    7. Resume from Hibernation
    8. Apply different authentication profile.
    9. Check Wireless Association / Authentication / Connection is established.
  • Stand alone/ Docked
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successfull
    Meeting Room Scenario
  • Apply 802.1x or such profile to connect to Office Network.
  • Check Profile is Associated ,Authenticated and Network Connection is established.
  • Suspend the System by Lid Close.
  • Take the system another room where same office network Access point is available.
  • Resume the system by opening LID.
  • Check Access Connection resumes connection with the same Wireless Profile , which was used before Suspend Operation.
  • Standalone
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successfull
    User Scenario Test -1
    1. Log in as Administrator and create LAN profile for wired connection using DHCP.
    2. Select disconnect from network when I switch to a different location profile.
    3. Create/apply wireless connection using DHCP and select disable wireless radio when I switch to a different location profile (the location profiles are seperate ones and not autoswitching).
    4. Verify that wired LAN connection is disabled and IP address released when switching to wireless connection.
    5. Verify that wireless connection is disabled and IP address is released when switching back to wired LAN connection.
    6. Create standard user account
    7. Logoff Administrator and login as the standard user
    8. Apply wired LAN profile, verify that IP address is assigned by DHCP server
    9. Select wireless profile and connect, verify that IP address is assigned
    10. run ipconfig /all, wired LAN connection will show IP 0.0.0.0
    11. Apply wired LAN connection without manually disconnecting from wireless connection, verify that IP for wired LAN is assigned
    12. run ipconfig /all,
    13. Confirm that WL connection is not activte and no IP address is assgined to WL adapter
    Standalone
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successfull
    User Scenario Test -2
    - Install Access Coonection and latest WL Driver.
    - Create a multiadapter profile in AC with Ethernet as first priority
    For Wireless settings, select the below settings-
    - Enter the SSID name
    - Select"Enabled-Use 802.1x-EAP CISCO(LEAP)
    - Select "Manual Prompt for LEAP User name and Password"
    - Select "No Network Connection unless User is logged in".
    - Save this profile ---this is the only profile on the system.
    - Restart the system system with the ethernet cable plugged into the
    system.
    - AC connects to the network using the ethernet card.
    - Check that the network works fine.
    - Now, remove the ethernet cable out of the system.
    - Confirm that the WL profile is connected successfully.
    Standalone
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successfull


    Day5- Day time - Check Item / Criteria
    Admin Mode
    User Mode
    Basic Profile Conectivity:
    Create and Apply profiles with following options. To know how to create a Wireless Profile / LEAP /WPA/WPA-TLS Profile, refer Test cases
    Wireless Security Funciton
    The link "Database 'PA Test Case', View 'Test Case\by Test_Item', Document 'Wireless Security Functions'" has been extracted
    ,2490PA
    Wireles Profile creation
    The link "Database 'PA Test Case', View 'Test Case\by Test_Item', Document 'Access Connections - Wireless profile Function'" has been extracted
    2178PA
    WPA-TLS No Error Message shall apprear from Access Connection

    Authentication shall be successfull

    Network Connection shall be successfull
    WPA-PSK (ASCI)
    Day-5 : Night timeWPA-PSK (Hex)
    802.1x EAP
    LEAP
    WEP
    Modem Profile
    Ethernet Profile
    VPN Profile
    Multiadapter Auto Profile (Ethernet + WPA PSK Profile) with Fastest available Network option
    Multiadapter Auto Profile (Ethernet + LEAP Profile) with Fastest available Network option
    Multiadapter Auto Profile (Ethernet + WPA-TLS Profile) with Fastest available Network option

    Inside "Wi-Fi" Cafe/Restaurant
    1. Boot the system to OS.
    2. Confirm WiFi connection either WWAN/WLAN.
    3. Open IE and do the following:
    - Search at Google
    - Watch Video Streaming at YouTube
    - Listen to Audio Streaming at IMEEM
    4. Press CTRL+ALT+DEL.
    5. Re-login and confirm that WiFi connection wasnt disrupted.
    6. Make VOIP/Internet based calls via Skype or Windows Live.
    7. Close the lid to enter S3.
    8. Open the lid to resume from S3.
    9. Repeat procedure 3.









    7. System successfully enters S3 without any errors.
    8. There are no display discrepancies, audio, or the like problems that happened upon resume from S3 through lid open.

    Network connection was disconnected for WWAN and requires manual relogin.

    Intel WLAN by default is auto-reconnect.
    WWAN: A
    WLAN: A
    WWAN: N/A
    WLAN: N/A
    WWAN: N/A
    WLAN: N/A




    Integration with all devices
    - Connect to Office network via Wireless using Access connection profile
    - Map shared network directory and transfer files.
    - While transferring files, send a fax using modem
    - Power ON Bluetooth device
    - Simultanously discover the other Bluetooth device
    - Transfer files to Public folder of other bluetooth device.
    - All devices to work correctly
    - No application crash
    - No system malfunction / performance degradation
    File copy - Stress test

    - Connect to Office network via Wireless using Access connection profile
    - Open mutliple applications like MS Office suite (Word,Excel,Powerpoint etc..)
    - Map shared network directory and transfer files of more than 1GB file size(ghost image)
    - Confirm that the network is working fine and system is stable in that condition
    Install Harddisk active protection driver
    From task tray, click the hard disk icon to invoke IBM Haddrive Protection system properties tab
    - Click Enable hard active protection system option
    - Click 'Temporarily disable hard drive active protection system while a repetitive vibration (such as that experienced when in a train or automobile) is detected
    - Select Show harddrive active protection icon on the system tray and
    Play sound when hard drive is spinning up or down.

    1. Connect to Office network via Wireless using Access connection profile
    2. Shake the system manually well to confirm that the Hard disk spinning process
    3. Confirm that the wireless still works fine.
    4. Map shared network directory and transfer files of more than 300MB file size (single file size)
    5. Confirm that the network is working fine and system is stable in that condition.

    Perform step 1-5 for all the wireless adapter and ethernet adapter also.
    Stand alone


    User Scenario Test

    Details
    Configuration
    Check Item / Criteria
    Win 8
    Win-7
    User Mode
    User Mode
    Home - Office Scenario
    1. Apply WEP Profile and connect to ADSL network.
    2. Verify Radio Association , Authentication and Network Connection is successfull
    3. Suspend the system and resume after 10 Minutes.
    4. Apply LEAP Profile of Campus Network.
    5. Verify Radio Association , Authentication and Network Connection is successfull
    6. Apply Multiadapter Profile (Ethernet + LEAP Profile,) with Fastest available Network option . As the Ethernet Cable is not connected, LEAP Wireless profile will be activated.
    7. Suspend the system and Dock the system to Supported Docking Station or Port replicator as applicable.
    8. Connect Ethernet Cable to Ethernet Port in Docking Station /Port Replicator.
    9. Resume from Suspend Mode.
    10. Access Connection shall resume connection to Ethernet profile automatically and IP Address shall be assigned.
    Stand alone/ Docked
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successfull
    • Wireless switching shall take place automatically without manual intervention
    A
    A
    Business User Switching Scenario
  • Apply VPN (IGN /VTS) profile
    1. Connect to Internet and Check connectivity.
    2. Connect to Campus network and Connect to office network
    3. Switch to WPA-TLS Profile
    4. Connect to Corporate File server and Copy the shared files to local system (300 MB)
    5. After File copying is finishd, Hibernate the system.
    6. Dock the System
    7. Resume from Hibernation
    8. Apply LEAPCKIP Profile
    9. Check Wireless Association / Authentication / Connection is established.
  • Stand alone/ Docked
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successful
    A
    A
    Meeting Room Scenario
  • Apply LEAP Profile
  • Check Profile is Associated ,Authenticated and Network Connection is established.
  • Suspend the System by Lid Close.
  • Take the system another room where similar LEAP Access point is available.
  • Resume the system by opening LID.
  • Check Access Connection resumes connection with the same Wireless Profile , which was used before Suspend Operation.
  • Standalone
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successful
    A
    A
    User Scenario Test -1
    1. Log in as Administrator and create LAN profile for wired connection using DHCP.
    2. Select disconnect from network when I switch to a different location profile.
    3. Create/apply wireless connection using DHCP and select disable wireless radio when I switch to a different location profile (the location profiles are seperate ones and not autoswitching).
    4. Verify that wired LAN connection is disabled and IP address released when switching to wireless connection.
    5. Verify that wireless connection is disabled and IP address is released when switching back to wired LAN connection.
    6. Create standard user account
    7. Logoff Administrator and login as the standard user
    8. Apply wired LAN profile, verify that IP address is assigned by DHCP server
    9. Select wireless profile and connect, verify that IP address is assigned
    10. run ipconfig /all, wired LAN connection will show IP 0.0.0.0
    11. Apply wired LAN connection without manually disconnecting from wireless connection, verify that IP for wired LAN is assigned
    12. run ipconfig /all,
    13. Confirm that WL connection is not activte and no IP address is assgined to WL adapter
    Standalone
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successful
    A
    A
    User Scenario Test -2
    - Install Access Coonection and latest WL Driver.
    - Create a multiadapter profile in AC with Ethernet as first priority
    For Wireless settings, select the below settings-
    - Enter the SSID name
    - Select"Enabled-Use 802.1x-EAP CISCO(LEAP)
    - Select "Manual Prompt for LEAP User name and Password"
    - Select "No Network Connection unless User is logged in".
    - Save this profile ---this is the only profile on the system.
    - Restart the system system with the ethernet cable plugged into the
    system.
    - AC connects to the network using the ethernet card.
    - Check that the network works fine.
    - Now, remove the ethernet cable out of the system.
    - Confirm that the WL profile is connected successfully.
    Standalone
    • No Error Message shall apprear from Access Connection
    • Authentication and NW connection shall be successfull
    A
    A


    TEST ITEM CONFIG Result
    Network
    Microsoft client and TCP/IP
    - Read (KB/sec)
    - Write (KB/sec)
    On board Ethernet
    - 10/100 Mbps
    - 10/100/1000Mbps (1 GB ethernet)
    BOTH
    AC & BATTERY mode
    Wireless LAN [Refer the support matrix for each product]
    - Test all the supported adapter
    BOTH
    AC & BATTERY mode
    Wireless WWAN [Refer the support matrix for each product]
    - Test all the supported adapter
    BOTH
    AC & BATTERY mode
    - Microsoft client and TCP/IP
    - Read (KB/sec)
    - Write (KB/sec)
    BOTH
    AC & BATTERY mode
    DHCP boot time



    Inside "Wi-Fi" & WWAN
    1. Boot the system to OS.
    2. Confirm WiFi connection either WWAN/WLAN.
    3. Open IE and do the following:
    - Search at Google
    - Watch Video Streaming at YouTube
    - Listen to Audio Streaming at IMEEM
    4. Press CTRL+ALT+DEL.
    5. Re-login and confirm that WiFi connection wasnt disrupted.
    6. Make VOIP/Internet based calls via Skype or Windows Live.
    7. Close the lid to enter S3.
    8. Open the lid to resume from S3.
    9. Repeat procedure 3.

    System successfully enters S3 without any errors.

    There are no display discrepancies, audio, or the like problems that happened upon resume from S3 through lid open.

    Note : Network connection if disconnected for WWAN requires manual relogin.

    WLAN by default is auto-reconnect.


    WiFi & WiMax
    1. Boot the system to OS.
    2. Confirm Network connection either WiMax/WLAN.
    3. Open IE and do the following:
    - Search at Google
    - Watch Video Streaming at YouTube
    - Listen to Audio Streaming at IMEEM
    4. Press CTRL+ALT+DEL.
    5. Re-login and confirm that network connection wasnt disrupted.
    6. Make VOIP/Internet based calls via Skype or Windows Live.
    7. Close the lid to enter S3.
    8. Open the lid to resume from S3.
    9. Repeat procedure 3.
    System successfully enters S3 without any errors.

    There are no display discrepancies, audio, or the like problems that happened upon resume from S3 through lid open.


    WLAN by default is auto-reconnect.


    Test Item
    RESULT
    Win-8
    Win-7
    Integration with all devices

    - Connect to Office network via Wireless using Access connection profile
    - Map shared network directory and transfer files.
    - While transferring files, send a fax using modem
    - Power ON WWAN Device
    - Simultanously connect to WWAN device
    - Browse net
    - Disconnect WWAN and connect to WiMax
    - Play files from youtube
    A


    CPU Sleep State confirmation ( LL-01261PA )
    THIS NEEDS TO BE TESTED FOR ALL THE SUPPORTED WLAN / WWAN ADAPTERS CONFIGURED CONDITION
    Win-8
    Win-7
    1. Boot OS in DC mode
    2. Open Power Manager with advanced mode
    3. Confirm "Deeper sleep" is enabled in Power Manager -> Power plan -> System settings.
    4. Install the Intel tool - 364532_CStResMon.exe as attached , in administrator mode and restart .
    5. Open performance monitor ( Start -> run -> Perfmon. ) .
    6. Click "Performance Monitor" on the left window and click green "+" sign .
    7. Select "intel C state Residency monitor" and add counter - "%C5/C6 Residency" . Click Ok .
    8. Check C5/C6 is recorded in DC mode ( in house case , it will be moved from 30 % to 65% ) ( See attached fig ) .
      ( for AC mode or if the CPU does not enter C5/C6 state, it is "0" ) .
    9. Start Access Connections, GPS application in DC mode .
    10. Apply AC WLAN / WAN profile .
    11. Check C5/C6 is recorded in DC mode ( in house case , it will be moved from 40 % to 65% ) ( See attached fig ) .
      Application should not prevent C5/C6 state .

    Attachment "364532_CStResMon.exe"can be seen at the bottom of the page.

    Attachment "C5 C6.jpg"can be seen at the bottom of the page.
    A
    A






    OTHER DETAILS
    EUT Quantity : Two systems 1. "Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead."
    2. "Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case)"
    (All Test Activity should be performed with AMT Enabled)
    Test Items Focus Remarks
    Wireless Function - Multiple adapters (Including on-board adapters)
    - Authentification method, Security
    - FnF5, F9
    Access Connection - Profile change in several situation
    - Wired, Wireless
    - ADSL, Dialup
    Application - IE
    - Outlook Express
    - Lotus Notes
    - VTS, SINE
    - Video Conference (TBD)
    - Install CSS as default



    Scenario Focus Remarks
    1. Wireless Roaming - Verify basic AccessConnection function
    - Use different Access Point (802.11b, 802.11a/b, 802.11a/g)
    - Move around in the office
    Add PM verification
    2. Profile change (Desktop -> Mobile) - Verify basic AccessConnection function
    - Docked -> undocked configuration
    Add PM verification
    3. Office -> Home environment - Wired network (office) -> ADSL (home)
    - Wireless network (office (outside)) -> Dialup (home) etc.
    Add PM verification
    4. Network performance monitor - Run monitor tool while test Check everyday
    5. Bluetooth, Mobile phone (PHS Data card) - Network environment co-existance
    6. Web Streaming (Longrun) - Web TV etc
    7. Wireless Adapter Performance using FnF5 / F9 - Verify WLAN and WWAN adapters functionality when Global/Software Switch On and Off.


    Test should be done using the latest Preload Image available at that time and update the necessary drivers.

    Only when Preload image is not available, ghost image can be used.

    Item
    Day 1
    Day 2
    Day 3
    Day 4
    Remarks
    Day time function test
    A
    A
    A
    A
    Night time long run test
    A
    A
    A
    A

    TEMS Reviewer Log:
    Review Logs
    Keywords:   None
    Requirements :   None
    Attached files :
    C5 C6.jpg - C5 C6.jpg (110945 bytes, ) 07/03/2015
    364532_CStResMon.exe - 364532_CStResMon.exe (2229190 bytes, ) 07/03/2015

    Update History:
    This document is not yet modified.