Test Case

Show / Hide direct link   <MAIN> 3633PA: Intel AMT credential Test for Managed devices - PP-80500



Version 1.3
Created on 02/03/2007 16:44:38  by Imthias Subaier
Summary
Preconditions
Status:   New
Priority:   Medium
BASIC INFORMATION
Section:S/W Test Require attachment:No
Team:Network Group:Advanced Function
Lessons Learned:No Phase:SIV (BBFV), SIT, SVT
Locations:Inhouse: AWS and Cambridge, Inhouse: AWS, Inhouse: Cambridge, Compal, Flextronics, Quanta, Wistron Owned By:Eiji Ogata/LENOVO
Objective:To confirm the reliability of AMt
CRITERIA
Change the Intel AMT password on all of the managed Intel AMT devices.
EUT QUANTITY
One system
EQUIPMENT
Network
Critical Attribute:[0] : ETN - Ethernet

CONFIGURATION
REFERENCE PROCEDURE
Refer detail section
STATISTIC INFO
Operating System Win81-64bit Win81-32bit Win10-32bit Win10-64bit Win7- 64bit Win7- 32bit Total
Test Points
Duration
Workload
# Step actions Win81-64bitWin81-32bitWin10-32bitWin10-64bitWin7- 64bitWin7- 32bit
1 Change the Intel AMT credentials for one device AAAAAA
2 Change the Intel AMT credentials for multiple device AAAAAA
3 AMT - Change the Intel AMT credentials from WebUI AAAAAA
4 AMT - 4.0/6.0 Intel Management & Security Status Task Tray Verification AAAAAA
DETAILS
ATTENTION!! Please follow below information.
1. Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead, then arrange to open defect, if needed.

2. Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case).

3. All Test Activity should be performed with AMT Enabled as Default (applicable on vPro enabled systems).

4. Please check Usability / Cosmetic issues (correct sentence/appropriate display/etc.) and open defect, if needed.

Change the Intel AMT credentials for one device

1. Open the LSM console (Start | All Programs | LANDesk | LANDesk System Manager). Double-click that AMT device in the My devices page, then click Hardware configuration | AMT | Provisioning | Configuration.

Change the Intel AMT credentials for multiple device
2. Open the LSM console (Start | All Programs | LANDesk | LANDesk System Manager) and click Hardware configuration | AMT | Provisioning | Configuration.


NOTE: 1. You can target all of the Intel AMT devices you want updated and set a new username and password for them. When you do this, the credentials are changed in both the database and on the Intel AMT devices.
2. Remember that only the Intel AMT credentials have a programmatic method to change them, but the ME credentials do not. The only way to change the ME credentials is by entering the ME BIOS on each device. If the ME credentials are forgotten, the only way to enter the ME or AMT BIOS again is to reflash the BIOS and firmware.


UR-1902
Test Item
Check Item / Criteria
Configuration
Result
Win XP
Win 7
Win 8
AMT Page user logon test (Using LDMS)

1. To test if the AMT credentials are changed, access the Intel AMT web page by entering the IP address in Internet Explorer.
Here are the access details:

For Small Business: https://x.x.x.x:16992
For Enterprise Mode: https://x.x.x.x:16993

AMT Page user logon test (Using AMT Page user accounts functionality)

1. In the AMT device webpage, click on User accounts link
2. Click on change admin button
3. Now input the desired user name password and click submit
4. Intel AMT logon prompt should pop-up
5. Input the old credentials
6. Logon should be denied
7. Now input the new credentials
8. Logon should be successful
9. Return to the Change administrator page and verify that the new username is displayed in the username field

  • Check if the credentials in logging on to the AMT webpage has been changed.
  • Verify that logon is successful




  • Check if the credentials in logging on to the AMT webpage has been changed.
  • Verify that logon is successful
Standalone
A
A
A
Blank Password Test (Using LDMS)
1. In LDMS server Manager, configure the AMT machine for no password. (Blank password configuration is not accepted)
2. Access the AMT device page and try to access the page without putting in any password

Blank Password Test (Using AMT Page user accounts functionality)

1. In the AMT device webpage, click on User accounts link
2. Click on change admin button
3. Now input a username and dont input any password
4. Click on submit
5. Blank password must not be accepted. Proper error message will be displayed on the user accounts page.
  • Blank Password should not be accepted in LDMS
  • Access to the AMT device page should be denied since no password was inputted

  • Blank Password should not be accepted in AMT user accounts function
  • Access to the AMT device page should be denied since no password was inputted
A
A
A
AMT Page Test
1. On the AMT device web page test, Status page should be displayed first.
2. Click on every link on the webpage and make sure that all links are working without any errors popping up
3. All sub-links and information must be displayed in the main page
  • Status page should display the correct information
  • Links should work as expected
A
A
A
AMT Page Event Log Test
1. Open LDMS server manager
2. On system defense test, apply a security policy.
3. Take note of the time and the security policy applied.
4. Launch AMT device webpage
5. Click on Event Log
6. Verify that Logs are displayed correctly in the event logs page
7. Check the time and the description of the event that has been logged.
  • Security policy changes should appear in AMT event log
  • Verify that the log displays the correct information (time, description)
A
A
A
AMT Page Remote Control Test
1. Open AMT device web page
2. On the left pane, click on remote control
3. Verify that the link is working
4. On the right portion of the device page, verify that the correct information is displayed
5. Select turn power off and click on the send command button
6. AMT system will now immediately turn off and AMT device web page status will display that the system is now turned off
7. On the remote control again, send a Power ON command to the AMT device
8. AMT device should power on and AMT device webpage should display correct information
9. Select Cycle power on and off and verify its function and its sub-functions one at a time.
  • Remote Control for all functions should work as expected
  • No error messages are expected when the commands are sent to the AMT device
  • AMT device webpage should display correct information upon command issue
  • No system malfunctions are expected when the commands are sent to the AMT device
A
A
A

AMT - Change the Intel AMT credentials from WebUI

1. Configure the AMT in target system and connect it to a network.
2. From another system in the network, type in http://<machine IP>:16992 in Internet explorer to access AMT WebUI.
3. When prompted, enter username and password ( admin:iAMT-6.0)
4. Click on User Account -> Change Admin..


5. Enter new User name and Password and click on Submit. Make sure the password entered fulfilsl the minimum requirements.


6. Internet explorer will immediately prompt for the new Username and password. Enter the new username and password and make sure login is successful.


UR-1997DS

AMT - 4.0 Intel Management & Security Status Task Tray Verification

Check Item / Criteria
Result
Test Item
Configuration
Win XP
Win 7
Win 8
1. Install Intel AMT 4.0 - Management Engine Interface driver and
Intel AMT 4.0 - Local Manageability Service and Serial Over
LAN driver and restart.
2. From the system tray click on the Intel Management & Security
Status Task Tray icon. Select Open. Confirm that the Intel
Management & Security Status application is launched properly
  • Make sure no Installation error appears and installation completes successfully.
  • Intel Management & Security Status application should launch properly. No error message should appear.
Standalone
A
A
A
1. From the system tray click on the Intel Management & Security Status Task Tray icon. Select Exit.
2. Confirm that the Intel Management & Security Status application
is closed properly
  • Intel Management & Security Status application should exit properly. No error message should appear.
A
A
A
General Tab
1. Launch Intel Management & Security Status window by double
clicking Intel Management & Security Status Task Tray icon.
2. Click General tab.
3. Confirm that all information is displayed correctly.
4. Check the Service Status for Intel Active Management
Technology (Intel AMT). It should be same as the status in ME
BIOS (press Ctrl-P as the device boots)
5. Check "Intel Management and Security Status will be available
next time I log on to Windows" option. Intel Management and
Security Status task tray icon should be available when you log
on to windows next time.
6. Uncheck "Intel Management and Security Status will be available
next time I log on to Windows" option. Intel Management and
Security Status task tray icon should not be available when you
log on to windows next time.
7. Check that "Enable User Notification Pop-Up" option is available
and it functions properly.

  • Service Status for Intel Active Management Technology (Intel AMT) should display Configured if it is Configured in ME BIOS.
  • Service Status for Intel Active Management Technology (Intel AMT) should display Unconfigured if it is not configured in ME BIOS.
Standalone
A
A
A
Intel AMT Tab
1. Launch Intel Management & Security Status window by double
clicking Intel Management & Security Status Task Tray icon.
2. Click Intel AMT tab.
3. Confirm that the following options are available and display
correct information:
(i) Intel AMT Status:
----------------------------
(a) Status Configured / Unconfigured
(b) Mode Enterprise / Small Business
(c) Firmware Version xxxxxxxxx

(ii) Advanced Information:
-------------------------------------
(a) Terminal/Keyboard Redirection
(b) Media Redirection
(c) System Defense State
(d) WebUI Status
(e) Last ME Reset Reason

(iii) Remote Connectivity:
------------------------------------
(a) Remote Connection Connected / Disconnected
(b) Connect / Disconnect button should work properly if the AMT
device is remotely connected to some other system.
4. Click Extended System Details button. Popup window should
appear and the following information should be displayed:
(a) System UUID
(b) MEI Driver
(c) LMS Driver
(d) Power Policy
5. Click Network Information button. Intel AMT Network Information
Popup window will appear. It should display correct information
for both Wireless and Wired Connection.

  • Extended System Details button should display the information correctly. System UUID should be correct. MEI Driver status and version should be correct. LMS Driver status and version should be correct. Power Policy should be same as configured in ME BIOS.
  • In Network Information tab following should be shown correctly for Wired Connection
    1. Mode- DHCP/Static
    2. Mac Information - Ethernet Mac Address
    3. Link Status - Link Up/Down
    4. IP Information - IP Address
  • In Network Information tab following should be shown correctly for Wireless Connection
    1. Mode- DHCP/Static
    2. Mac Information - Wireless Card Mac Address
    3. Link Status - Link Up/Down
    4. IP Information - IP Address
    5. Configured for Wireless
    6. Controlling the interface

Standalone
A
A
A

AMT 6.0 - Intel Management & Security Status Task Tray Verification - UR2519

Check Item / Criteria
Result
Test Item
Configuration
Win XP
Win 7
Win 8
1. Install Intel AMT 6.0 - Management Engine Interface driver and
Intel AMT 6.0 - Local Manageability Service and Serial Over
LAN driver and restart.
2. From the system tray click on the Intel Management & Security
Status Task Tray icon. Select Open. Confirm that the Intel
Management & Security Status application is launched properly
  • Make sure no Installation error appears and installation completes successfully.
  • Intel Management & Security Status application should launch properly. No error message should appear.
Standalone
A
A
A
1. From the system tray click on the Intel Management & Security Status Task Tray icon. Select Exit.
2. Confirm that the Intel Management & Security Status application
is closed properly
  • Intel Management & Security Status application should exit properly. No error message should appear.
A
A
A
General Tab
1. Launch Intel Management & Security Status window by double
clicking Intel Management & Security Status Task Tray icon.
2. Click General tab.
3. Confirm that all information is displayed correctly.
4. Check the Service Status for Intel Active Management
Technology (Intel AMT). It should be same as the status in ME
BIOS (press Ctrl-P as the device boots)
5. Check "Intel Management and Security Status will be available
next time I log on to Windows" option. Intel Management and
Security Status task tray icon should be available when you log
on to windows next time.
6. Uncheck "Intel Management and Security Status will be available
next time I log on to Windows" option. Intel Management and
Security Status task tray icon should not be available when you
log on to windows next time.
7. Check that "Enable User Notification Pop-Up" option is available
and it functions properly.

  • Service Status for Intel Active Management Technology (Intel AMT) should display Configured if it is Configured in ME BIOS.
  • Service Status for Intel Active Management Technology (Intel AMT) should display Unconfigured if it is not configured in ME BIOS.
Standalone
A
A
A
Intel AMT Tab
1. Launch Intel Management & Security Status window by double
clicking Intel Management & Security Status Task Tray icon.
2. Click Intel AMT tab.
3. Confirm that the following options are available and display
correct information:
(i) Fast Call for help Connected/Disconnected

(ii) Support session status
-------------------------------------
(a) Remote Control Connection
(b) Disconnected hot key
(c) Media Redirection
(d) Terminal and Keyboard Redirection

(iii) System Defense
------------------------------------
(a) Status Activated / Not activated /Info Unavailable




? Remote Control Connection
Indicates whether there is any open KVM (Keyboard, Video & Mouse) Remote Control session (Connected / Disconnected / Information unavailable) .
Click the Stop Session button to close and open Remote control session.

? Disconnection hot key
Indicates what is the hot key used to close an open KVM (Keyboard, Video, Mouse) Remote Control session (default is Shift+Esc).
Click on the Change button to choose a different hot key for terminating an open KVM Remote control session

? Media Redirection
Indicates whether there are any open IDE redirection sessions. Possible values: Connected/ Disconnected/ Information unavailable

?Terminal/Keyboard Redirection
Indicates whether there are any open terminal/keyboard redirection sessions. Possible values: Connected/ Disconnected/ Information unavailable.

. System Defense State
Indicates whether System Defense is currently active. Possible values: Activated/Not activated/ Information unavailable.
Standalone
A
A
A
Advanced Tab

1. Launch Intel Management & Security Status window by double
clicking Intel Management & Security Status Task Tray icon.

2. Click Advanced Tab.

3. Confirm that the following options are available and display
correct information:
(i) Intel Management Engine
------------------------------------------
(a) Status Configured / Unconfigured
(b) Firmware Version 6.0.0.xxxx

(ii) Secure Output Window Settings
-------------------------------------
(a) Message Language
(b) Message Size

(iii) Network Information
-----------------------------------
(iv) Extended System Details


4. Click Network Information button. Intel AMT Network Information
Popup window will appear. It should display correct information
for both Wireless and Wired Connection.

(i) IPv4 Mode
(ii) MAC Information
(iii) Link Status
(iv) IP Information









5. Click Extended System Details button. Popup window should
appear and the following information should be displayed:
(a) Intel MEI Driver
(b) LMS
(c) Power Policy
(d) Last Intel ME Reset Reason
(e) System UUID


? State
The operational status of Intel? ME Possible values: Configured / Unconfigured / Information unavailable.

? Firmware Version
The Intel? ME firmware version.


? Message Language
Specifies the language used by the Secure Output feature. Choose one of the following: English, French ,German, Chinese (traditional), Japanese

?Message Size
Specifies the font size of messages displayed by Secure Output Feature. Choose one of the following: Regular or Large



IPv4 Mode
Possible values: Static/DHCP/Information unavailable.

?MAC Information
XX:XX:XX:XX:XX:XX ? e.g. 88:88:88:0A:88:87

?Link Status
Whether the link is currently active. Possible values are: Link up/Link down/Information unavailable

?IP Information
X.X.X.X ? e.g. 10.102.0.1

? Intel? MEI Driver
The version of the Intel? Manageability Engine Interface driver.

?LMS
The version of the LMS service.

?Power Policy
The power policy which is currently in effect. States are: ON in S0, or any other power policy supported by the system.

?Last Intel? ME Reset Reason
Displays the reason that the Intel? ME was last reset. Possible values: Global System / FW reset / Power Up / Unknown cause / Information unavailable

?System UUID
The current System Unique Universal Identification. Standard System UUID presentation, such as, 03000200-0400-0500-0006-000700080009.
A
A
A

OTHER DETAILS
EUT Quantity : One system 1. "Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead."
2. "Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case)"
(All Test Activity should be performed with AMT Enabled)
Test Item XP V32 V64

TEMS Reviewer Log:03/05/2007 10:30:25 AM by Kazuo 1 Matsumoto/Japan/Lenovo/IDE (Review Comment: OK
Review Logs
Keywords:   None
Requirements :   None
Attached files :

Update History:
This document is not yet modified.