Test Case

Show / Hide direct link   <MAIN> 5764PA: W10: PM Events Operation and Priority - PP-81351



Version 1.3
Created on 23/02/2017 11:22:10  by m_komatsu
Last modified on  23/02/2017 11:50:58  by m_komatsu
Summary
1. Define Various Power State
    Define Entering Operation to the Power state of Sleep, Shutdown and Restart
    Define Resume Operation from the Power state of Sleep and Shutdown
 
2. Define Priority for choice upon Test deepness, e.g.
    FVT/SIT Full: Mandatory, High, Medium, Low
    Regression: Mandatory, High, Medium
    FFRT: Mandatory, High
    Quick Regression: Mandatory
 
3. Remind Terms of Power State
    This will follow OS Power Menu, though MS defines "Sleep" is for Standby and Hibernate 
    in some packages.
 
    Sleep       CS(Connected Standby)=AOAC(Always On Always Connected)
      DS(Disconnected Standby)
      S3=LS(Legacy Standby)
 
    Hibernate S4=Hibernate:Deeper sleep state than Standby (S3 or MS)
 
    Shutdown HS(Hybrid Shutdown) (W10, W8)
        FS(Full Shutdown) (W7)
 
note:MS(Modern Standby=S0iX), including CS and DS
Preconditions

 1. Identify Product category and Supporting Power State and Default settings, 

    e.g. ClamShell, Tablet+Thin/ProKBD, Tablet, Yoga(TBD)
    e.g. On some Tablet before KabyLake-R, DS(Default)&CS
    e.g. On some KabyLake-R or Later, WWAN:CS only, WLAN Only:CS(Default)&DS
Status:   In Review
Priority:   Mandatory
REVIEW CYCLE
Originator Miyuki Komatsu
Current Reviewer Eiji Ogata
Future Reviewer/s None
BASIC INFORMATION
Section:S/W Test Require attachment:No
Team:Network Group:Power Management
Lessons Learned:No Phase:FVT, SVT, Post GA, SIT
Locations:Inhouse: AWS, Inhouse: Cambridge, Compal, Quanta, Wistron Owned By:Eiji Ogata/LENOVO
Objective:Define Various S3 and S4
CRITERIA

TBD

EUT QUANTITY

None

EQUIPMENT

None

Critical Attribute:Chip Set, PM driver, OS
CONFIGURATION

None

REFERENCE PROCEDURE

Refer to attached Test Procedure

STATISTIC INFO
Operating System Win10-32bit Win10-64bit Total
Test Points
Duration
Workload
DETAILS
ATTENTION!! Please follow below information.
1. Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead, then arrange to open defect, if needed.

2. Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case).

3. All Test Activity should be performed with AMT Enabled as Default (applicable on vPro enabled systems).

4. Please check Usability / Cosmetic issues (correct sentence/appropriate display/etc.) and open defect, if needed.

Refer to attached Test Procedure

OTHER DETAILS
TEMS Reviewer Log:
Review Logs
Keywords:   None
Requirements :   None
Attached files :
Test Procedure - 5764PA_W10_PM Events Operation and Priority_20170223.xlsx (27570 bytes, application/vnd.openxmlformats-officedocument.spreadsheetml.sheet) 23/02/2017
ATS Input : PM Event Scenario - 5764PA_W10_PM Events Scenario_1-1_20160909.txt (795 bytes, text/plain) 09/09/2016
Update History:
Modified last: 2017-02-23 11:50:58.193, by Miyuki Komatsu, Update Summary & Preconditions
Version Update History:
2017-02-23 11:22:10, Version 1.3, m_komatsu, Add CS=AOAC in Objective section in attached Test Procedure
2016-09-09 19:06:50, Version 1.2, m_komatsu_nw, Add PM Event Scenario 1-1, 1-2
2016-09-02 18:14:39, Version 1.1, m_komatsu_nw, Upgrade Priority of TimerHibernate, because some case, Default Enabled ClamShell (DC:3hours, AC:3hours) Tablet (DC:4hours, AC:Never)

Other versions
Version 1.2


Version 1.2
Created on 09/09/2016 19:06:50  by m_komatsu_nw
Summary

 1. Define Various S3 and S4

       Define entering Operation to the specific S3 and S4
       Define Resume Scenario from the specific S3 and S4
 
2. Define Priority for choice upon Test deepness, e.g.
       FVT/SIT Full:         Mandatory, High, Medium, Low
       Regression:           Mandatory, High, Medium
       FFRT:                    Mandatory, High
       Quick Regression:  Mandatory
Preconditions
Status:   Review Complete
Priority:  
BASIC INFORMATION
Section:S/W Test Require attachment:No
Team:Network Group:Power Management
Lessons Learned:No Phase:FVT, SVT, Post GA, SIT
Locations:Inhouse: AWS, Inhouse: Cambridge, Compal, Quanta, Wistron Owned By:Eiji Ogata/LENOVO
Objective:Define Various S3 and S4
CRITERIA

TBD

EUT QUANTITY

None

EQUIPMENT

None

Critical Attribute:Chip Set, PM driver, OS
CONFIGURATION

None

REFERENCE PROCEDURE

Refer to attached Test Procedure

STATISTIC INFO
Operating System Win10-32bit Win10-64bit Total
Test Points
Duration
Workload
DETAILS
ATTENTION!! Please follow below information.
1. Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead, then arrange to open defect, if needed.

2. Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case).

3. All Test Activity should be performed with AMT Enabled as Default (applicable on vPro enabled systems).

4. Please check Usability / Cosmetic issues (correct sentence/appropriate display/etc.) and open defect, if needed.

Refer to attached Test Procedure

OTHER DETAILS
TEMS Reviewer Log:
Review Logs
Created last 2016-09-12 18:40:04 by Eiji Ogata. Review Comments(Review Complete): review completed.
Keywords:   None
Requirements :   None
Version Update History:
This document is not yet modified.

Version 1.1


Version 1.1
Created on 02/09/2016 18:14:39  by m_komatsu_nw
Summary

 1. Define Various S3 and S4

       Define entering Operation to the specific S3 and S4
       Define Resume Scenario from the specific S3 and S4
 
2. Define Priority for choice upon Test deepness, e.g.
       FVT/SIT Full:         Mandatory, High, Medium, Low
       Regression:           Mandatory, High, Medium
       FFRT:                    Mandatory, High
       Quick Regression:  Mandatory
Preconditions
Status:   New
Priority:  
BASIC INFORMATION
Section:S/W Test Require attachment:No
Team:Network Group:Power Management
Lessons Learned:No Phase:FVT, SVT, Post GA, SIT
Locations:Inhouse: AWS, Inhouse: Cambridge, Compal, Quanta, Wistron Owned By:Eiji Ogata/LENOVO
Objective:Define Various S3 and S4
CRITERIA

TBD

EUT QUANTITY

None

EQUIPMENT

None

Critical Attribute:Chip Set, PM driver, OS
CONFIGURATION

None

REFERENCE PROCEDURE

Refer to attached Test Procedure

STATISTIC INFO
Operating System Win10-32bit Win10-64bit Total
Test Points
Duration
Workload
DETAILS
ATTENTION!! Please follow below information.
1. Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead, then arrange to open defect, if needed.

2. Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case).

3. All Test Activity should be performed with AMT Enabled as Default (applicable on vPro enabled systems).

4. Please check Usability / Cosmetic issues (correct sentence/appropriate display/etc.) and open defect, if needed.

Refer to attached Test Procedure

OTHER DETAILS
TEMS Reviewer Log:
Review Logs
Created last 2016-09-02 19:25:07 by Eiji Ogata. Review Comments(Review Complete): review completed.
Keywords:   None
Requirements :   None
Version Update History:
This document is not yet modified.

Version 1


Version 1
Created on 01/09/2016 12:04:33  by m_komatsu_nw
Last modified on  01/09/2016 13:32:18  by m_komatsu_nw
Summary

 1. Define Various S3 and S4

       Define entering Operation to the specific S3 and S4
       Define Resume Scenario from the specific S3 and S4
 
2. Define Priority for choice upon Test deepness, e.g.
       FVT/SIT Full:         Mandatory, High, Medium, Low
       Regression:           Mandatory, High, Medium
       FFRT:                    Mandatory, High
       Quick Regression:  Mandatory
Preconditions
Status:   New
Priority:  
BASIC INFORMATION
Section:S/W Test Require attachment:No
Team:Network Group:Power Management
Lessons Learned:No Phase:FVT, SVT, Post GA, SIT
Locations:Inhouse: AWS, Inhouse: Cambridge, Compal, Quanta, Wistron Owned By:Eiji Ogata/LENOVO
Objective:Define Various S3 and S4
CRITERIA

TBD

EUT QUANTITY

None

EQUIPMENT

None

Critical Attribute:Chip Set, PM driver, OS
CONFIGURATION

None

REFERENCE PROCEDURE

Refer to attached Test Procedure

STATISTIC INFO
Operating System Win10-64bit Total
Test Points
Duration
Workload
DETAILS
ATTENTION!! Please follow below information.
1. Please check Error and Warning message in Event Viewer before you start the test case and after you complete the test case, and report it to your team lead, then arrange to open defect, if needed.

2. Perform All Test in Battery Mode (Some of the test items need to perform in AC Mode, follow each Test Case).

3. All Test Activity should be performed with AMT Enabled as Default (applicable on vPro enabled systems).

4. Please check Usability / Cosmetic issues (correct sentence/appropriate display/etc.) and open defect, if needed.

Refer to attached Test Procedure

OTHER DETAILS
TEMS Reviewer Log:
Review Logs
Created last 2016-09-01 15:28:16 by Eiji Ogata. Review Comments(Review Complete): review completed.
Keywords:   None
Requirements :   None
Version Update History:
Modified last: 2016-09-01 13:32:18.618, by Miyuki Komatsu_nw, Initial
Modified last: 2016-09-01 13:30:25.484, by Miyuki Komatsu_nw, Initial
Modified last: 2016-09-01 13:25:55.581, by Miyuki Komatsu_nw
Modified last: 2016-09-01 13:25:55.05, by Miyuki Komatsu_nw
Modified last: 2016-09-01 13:25:53.943, by Miyuki Komatsu_nw